The top layer of a trail.
Search Results "Side Transfer Surface"
Filters
Commonly Searched Documents
-
Surface
-
Initial Measures and Transfer Setup
However, for the setup of the baseline level transfer (when the person and mobility device were in a position next to platform ready to transfer), if there was a noticeable difference (one...
-
Side Approach
Side Approach Side reach depth is important to consider in the design and location of sinks....
-
Side Approach
Side Approach Where space is provided for a side approach, controls can be mounted at the heights allowed for side reaches....
-
Surface
Surface—The top layer of ground on a recreation site, outdoor recreation access route, trail, or beach access route Firm. A surface that resists deformation by indentations....
-
Grab Bar and Backrest Evaluation
The grab bars were frequently used as handhelds during the transfer process and for one person it made the difference of being able to do a non-level transfer to the platform....
-
802.1.1 Floor or Ground Surface
The floor or ground surface of wheelchair spaces shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
802.1.1 Floor or Ground Surface
The floor or ground surface of wheelchair spaces shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
Surface, Slope, and Openings [1011.2.2, 1011.2.3, and 1011.2.4]
The surface of the clear ground space must be firm and stable. Additional information on firm and stable surfaces is provided in the trails section of this guide....
-
4.3.6 Surface Textures
The surface of an accessible route shall comply with 4.5....
-
4.3.6 SURFACE TEXTURES
The surface of an accessible route shall comply with 4.5....
-
Acceptable Trail Surfacing Requirements
Trail surfaces are currently considered accessible only if the surfacing material is firm, stable, and slip-resistant and the trail has the engineered attributes of adequate width, moderately...
-
Ramp
Ramp: A ramped surface was designed to insert between two steps and serve as an integrated sliding board to assist with the transfers by bridging the gap between steps. ...
-
Entry Points and Seats: ADA Standard Section 1008.4.4
Where play components require transfer to entry points or seats, the entry points or seats shall be 11 inches (280 mm) minimum and 24 inches (610 mm) maximum from the clear floor or ground...
-
Ticket transfer. (Section-by-Section Analysis)
Ticket transfer. The Department received many comments asking whether accessible seating has the same transfer rights as general seats....
-
11B-1008.4.4 Entry points and seats
Where play components require transfer to entry points or seats, the entry points or seats shall be 11 inches (279 mm) minimum and 24 inches (610 mm) maximum from the clear floor or ground...
-
Side Entry Openings, and Width and Length of Wheelchair Space
Side Entry Openings, and Width and Length of Wheelchair Space If the wheelchair space can only be entered from the side, the ride must be designed to permit sufficient turning space for...
-
Bonded Impact/cushioning Surfaces
Bonded Impact/cushioning Surfaces Eight different surface test specimens were formed with surface dimensions of 1.2m x 1.2m with a depth of 0.3m (48”x48”x 12”) in Madison WI (Figure 1...
-
1018.3 Surface
The surface of beach access routes and resting intervals shall be firm and stable....
-
1018.3 Surface
The surface of beach access routes and resting intervals shall be firm and stable....
-
810.2.1 Surface
Bus stop boarding and alighting areas shall have a firm, stable surface....
-
810.2.1 Surface
Bus stop boarding and alighting areas shall have a firm, stable surface....
-
1018.3 Surface
This section requires the surface of beach access routes and resting intervals to be firm and stable....
-
Firmness or Firm Surface
Firmness or Firm Surface. A firm surface resists deformation by either indentations or particles moving on its surface (2010 ADA Standards for Accessible Design, Advisory 302.1). ...