Section 904.2 requires that “[a]ll portions of counters required to comply with 904 shall be located adjacent to a walking surface complying with 403.” 2010 Standards § 904.2....
Search Results "Hybrid Surface System"
Filters
Commonly Searched Documents
-
B. The ADA Standards for Accessible Design
-
C. Raised Porches Are Part Of the Store That Must Be Made Accessible and Located On An Accessible Route
Pursuant to Chapter 3, accessible spaces must have compliant floor surfaces, compliant turning space, and compliant clear floor space, among other requirements. 2010 Standards, §§ 301-309...
-
American Standard Decorum 0.125 gpf High Efficiency Urinal Top Spud
Deep sump reduces splashing Washout urinal works at 0.125 gpf (0.47 Lpf) Permanent EverClean® surface inhibits the growth of stain and odor-causing bacteria, mold, and mildew on the surface...
-
1. Executive Summary
access routes to be provided within pedestrian circulation paths located in the public right-of-way, and would establish proposed technical provisions for the width, grade, cross slope, and surface...
-
Tormax Technologies iMotion® TN 110 In-Floor Swing Door Operator (High and Low Energy)
Approved for use in Historic Buildings Conforms with ADA guidelines Surface or flush mount floor boxes Smooth and silent operation Programmable iMotion® microprocessor...
-
Midmark 630 HUMANFORM™ Procedures Table
Sensing Technology™ (AST) enhances patient and provider safety by helping avoid harmful impact during movement, such as objects being caught under the seat and footrest Premium Comfort System...
-
2. Electronic (Digital) Level
Note: Some architects use a "rise over run" formula to calculate the slope of a surface....
-
11B-1003.3.2 Boarding pier clearances
At high water, the entire chain is floating and a transition plate connects the first float to the surface of the launch ramp....
-
1003.3.2 Boarding Pier Clearances
At high water, the entire chain is floating and a transition plate connects the first float to the surface of the launch ramp....
-
Value Contrast (slide 9)
Fixed Surfaces To show where vertical and horizontal surfaces meet is very important. To show edges is very important....
-
1003.3.2 Boarding Pier Clearances
At high water, the entire chain is floating and a transition plate connects the first float to the surface of the launch ramp....
-
Telescopes and Periscopes
Whenever a telescope or periscope is provided, ensure that a separate telescope or periscope is available for use from a standing position (60 inches above the floor or ground surface is...
-
Trail Slopes
Cross slopes—the side-to-side slope of a trail tread (figure 131)—provide drainage to keep water from ponding and damaging the trail, especially on unpaved surfaces....
-
308.3.2 Obstructed High Reach
Operable parts of fuel dispensers shall be permitted to be 54 inches (1370 mm) maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs...
-
106.5.45 Primary Function
a primary function include, but are not limited to: (i) Remodeling merchandise display areas or employee work areas in a department store; (ii) Replacing an inaccessible floor surface...
-
G. Sleeping Areas
Accessible cots have a sleeping surface at approximately the same height above the floor as the seat of a wheelchair (17 to 19 inches above the floor)....
-
308.3.2 Obstructed High Reach
Operable parts of fuel dispensers shall be permitted to be 54 inches (1370 mm) maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs...
-
F216.13 Trailhead Signs
The technical requirements in 1017.11 require the signs to include information on the length of the trail or trail segment; surface type; typical and minimum tread width; typical and minimum...
-
1016.1 General
The technical requirements address the surface of outdoor recreation access routes, passing spaces, and resting intervals (1016.2); the clear width of outdoor recreation access routes (1016.3...
-
Location
An accessible route never has curbs or stairs, must be at least 3- feet wide, and has a firm, stable, slip-resistant surface....
-
Suggested best practices for architects and other design professionals
architects and other design professionals As the construction industry works to develop standards for construction tolerances related to specific materials and applications for accessible surfaces...
-
Signage
Signs should not be made of reflective materials such as brass, silver, gold, glass, or mirrored surfaces unless there is an additional properly located sign that complies with the Standards...
-
Location
An accessible route never has curbs or stairs, must be at least 3- feet wide, and has a firm, stable, slip-resistant surface....
-
240.2.2 Elevated Play Components
For purposes of this section, ramps, transfer systems, steps, decks, and roofs are not considered elevated play components....
