Mounts flush against side wall in accessible toilet compartment to allow clearance for grab bar above unit has toilet tissue dispenser on left side of unit....
Search Results "Toe Clearance"
Commonly Searched Documents
- Bobrick B-3091 ClassicSeries® Recessed-Mounted Toilet Tissue, Seat-Cover Dispenser and Waste Disposal
- Bobrick B-3092 ClassicSeries® Recessed-Mounted Toilet Tissue, Seat-Cover Dispenser and Waste Disposal
- 
    
  
  4. Bed transfer space
  4. Bed transfer space: A 30-inch by 48-inch clear floor space facilitates transfer from a wheelchair to the bed. 
- 
    
  
  5. Bed with clear floor space
  5. Bed with clear floor space for a side approach next to bed. 
- 
    
  
  R402 Protruding Objects
  R402 Protruding Objects 
- 
    
  
  4.8.5(3)
  (3) The clear space between the handrail and the wall shall be 1 - 1/2 in (38 mm). 
- 
    
  
  1010.1.5 Floor elevation
  There shall be a floor or landing on each side of a door. Such floor or landing shall be at the same elevation on each side of the door. Landings shall be level except for exterior... 
- 
    
  
  11B-404.2.4.4 Floor or ground surface
  Floor or ground surface within required maneuvering clearances shall comply with Section 11B-302.... 
- 
    
  
  306 Knee and Toe Clearance
  Section 306 defines the minimum clearances for knees and toes beneath fixed objects. Few comments addressing this section were received.... 
- 
    
  
  Entrance Landings
  Entrance landings must accommodate door maneuvering clearances as well as landings for provided ramps. Entrance Landing... 
- 
    
  
  Clearances between a handrail and wall surface: 2012 NFPA 101 vs. 2010 ADA
  Question/Issue: According to the new 2012 NFPA 101 Life Safety Code, Chapter 7, Section 7.2.2.4.4.5 & Exhibit 7.97, the finger clearance at an existing stair handrail should be... 
- 
    
  
  Boat Slip Clearance: ADA Standard Section 1003.3.1
  Advisory 1003.3.1 Boat Slip Clearance Exception 3.... 
- 
    
  
  Doors
  Main Lobby restroom: provide a restroom vestibule door with at least 18" of maneuvering clearance on the latch side of the door. See Standards § 4.13.6.... 
- 
    
  
  Plan 3A: 12-Foot Wide Accessible Guest Room
  ); • Circular turning space in room (section 603.2.1); • Required clear floor spaces at fixtures and turning space overlap (section 603.2.2); • Turning space includes knee and toe... 
- 
    
  
  Plan 1A: 13-Foot Wide Accessible Guest Room
  ); • Circular turning space in room (section 603.2.1); • Required clear floor spaces at fixtures and turning space overlap (section 603.2.2); • Turning space includes knee and toe... 
- 
    
  
  Plan 1B: 13-Foot Wide Accessible Guest Room
  ); • Circular turning space in room (section 603.2.1); • Required clear floor spaces at fixtures and turning space overlap (section 603.2.2); • Turning space includes knee and toe... 
- 
    
  
  Doorways at Landings [§405.7.5]
  Doorways at Landings [§405.7.5] Required door maneuvering clearances can overlap ramp landings (it is advisable to locate the swing of doors outside ramp landings for greater safety).... 
- 
    
  
  M302.4.2 Clearance Around Base
  The base of the equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface... 
- 
    
  
  M302.4.2 Clearance Around Base
  The base of the diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination... 
- 
    
  
  D4
  On the latch, pull side of the door, is there at least 18 inches clearance provided if the door is not automatic or power-operated?... 
- 
    
  
  11B-503.5 Vertical clearance
  spaces, access aisles serving them, and a vehicular route from an entrance to the passenger loading zone and from the passenger loading zone to a vehicular exit shall provide a vertical clearance... 
- 
    
  
  11B-503.5 Vertical clearance
  Advisory 11B-503.5 Vertical clearance. ... 
- 
    
  
  Circular Cross Section and Clearance (§505.5, §505.7)
  Circular Cross Section and Clearance (§505.5, §505.7)... 
