A rectangular area usually two club-lengths in depth, the teeing ground’s borders are defined by the outside limits of two “tee-markers.”...
Search Results "Submerged Depth"
Filters
Commonly Searched Documents
-
Teeing Grounds
-
5.3.2 Transfer Sides Recommendations for M301
The transfer surface shall be located to provide options to transfer from a mobility device onto one short side (depth) and one long side (width) of the surface....
-
5.7.1 Lift Compatibility Clearance in Base for M301
Where the width of the examination surface is less than 36 inches, the clearance depth shall extend the full width of the equipment....
-
809.2.2 Turning Space
EXCEPTION: Turning space shall not be required in exterior spaces 30 inches (760 mm) maximum in depth or width. Advisory 809.2.2 Turning Space....
-
15. Can I store my lift and bring it out only when it is requested by a person with a disability?
In addition, the ADA Standards specify that a lift must be located at the proper water depth and with the necessary space around it to maneuver a wheelchair....
-
11B-705.2 Detectable directional texture
The depth of the texture shall not be less than 36 inches (914 mm)....
-
Tork Toilet Seat Cover Dispenser White
Product Data System - V1 - toilet seat cover system Material - Plastic Height - 12.4 in Width - 16.7 in Depth - 2.3 in Color - White...
-
Bobrick ConturaSeries Recessed Sanitary Napkin Disposal B-4353
Rough Wall Opening: 11 1/4" W, 9 1/2" H, 4" min. depth (285 x 240 x 100mm)....
-
Bobrick Countertop-Mounted Circular Waste Chute B-529
Outside diameter 6 15/16" (175mm), inside diameter 5 1/2" (140mm), chute depth 5" (130mm). Rough Countertop Cutout: 5 5/8" diameter (140mm)....
-
Playground Study Site
The remaining area of approximately 190 m2 (2,020 ft2 ) was converted to a full-depth EWF surface (Fig. 1)....
-
Re: Service Counters
The entire depth of the lowered counter at 34" max height must be provided to allow for this unimpeded interaction instead of the higher employee counter condition which prevents equal access...
-
Bobrick TrimLineSeries Recessed Sanitary Napkins Disposal B-35303
Rough Wall Opening: 11 1⁄2" W, 17 1⁄4" H, 3 3⁄4" min. depth (290 x 440 x 95mm)....
-
Tork Toilet Seat Cover Dispenser
Product Data System - V1 - toilet seat cover system Material - Plastic Height - 12.4 in Width - 16.7 in Depth - 2.3 in Color - Black...
-
Bobrick TrimLineSeries Recessed Paper Towel Dispenser B-35903
Rough Wall Opening: 11 1⁄4" W, 15 5⁄8" H, 4" min. depth (285 x 395 x 100mm)....
-
Bobrick Recessed Paper Towel Dispenser/Waste Receptacle B-39003
Rough Wall Opening: 16" W, 54 3⁄4" H, 7 7⁄8" min. depth (405 x 1390 x 200mm)....
-
Bobrick ClassicSeries Recessed Sanitary Napkins Disposal B-353
Rough Wall Opening: 11 1/4" W, 15 5/8" H, 4" min. depth (285 x 395 x 100mm)....
-
Re: Service Counters
For code compliance, one must create a reasonable standard for sufficient depth for accessible use. Reasonable persons will disagree on that number. Why bother? ...
-
M305.2.2 Length (Section-by-Section Analysis)
there was no requirement for length of the transfer support; however, the MDE NPRM preamble noted that the Access Board was considering requiring the transfer supports to extend the entire depth...
-
M301.3.1 Transfer Supports
A) For transfer depths less than or equal to 24 inches a transfer support will be located opposite the transfer side....
-
Moisture and Durability
The trendline fitted to the data of the moisture profile in E2 indicates that it is saturated at a depth of approximately 100 mm (4”) and continues to be saturated to the drainage bed....
-
How to Measure Transfer Surface Height
The lower wheelchair illustrates a typical diagonal transfer.24 Figure 11: Corner radii of a medical examination table The depth and width are measured along the centerlines of...
-
Test Procedures
The EWF surface was excavated throughout its entire 0.3-m (12-in.) depth to determine the moisture profile of the surfacing system....
