In a wheelchair accessible compartment with a door located in the front wall or partition (facing the water closet), either in-swinging or out-swinging, a minimum 60 inches (1524 mm)...
Search Results "Pull Side"
Filters
Commonly Searched Documents
-
11B-604.8.1.1.3 Maneuvering space with end-opening door
-
Sargent HP Bored Lock with Push/Pull Trim
The HP Series Bored Lock with ALP push/pull trim has ligature resistant features and provides an aesthetically-pleasing alternative to standard push/pull products....
-
5.4.1.1 Transfer Support Location for Stretchers
The transfer surface for stretchers should be oriented along the long side of the surface....
-
A. Passenger Drop-Off Areas
A. Passenger Drop-Off Areas During an evacuation the most efficient method of transporting people to shelters likely will include using vans and buses. Accessible buses and vans...
-
Wall furr-out to support a grab bar when toilet is too far from the side wall
Here's a good example of one solution for a water closet that's too far from the adjacent side wall. ...
-
5.2.1.3 Transfer Surface Size for Stretchers
The transfer surface should be 28 inches wide minimum and 17 inches deep minimum located on both long sides of stretchers....
-
4.1.1 Range of Examination Table and Chair Configurations
Equipment designed for patients in prone or side-lying positions (M301) Examination tables Podiatry tables 2....
-
Trimco 1500 Series Hospital Latch
Trimco’s 1500 Series Push/Pull Latches features a sleekly designed, cold-forged steel base assembly....
-
Figure 604.5.1 Side Wall Grab Bar at Water Closets – Drawing from the U.S. Access Board
-
308.3.1 Automatic Trash Can Height
-
Reach Ranges and Operability Requirements
Design Tip Understand forward reach and side reach terminology....
-
Re: 404.2.4.3 Recessed Doors and Gates
A barrier within 18" of the latch side of a push approach door will trigger the extra requirements....
-
5.2 Transfer Surface Size for Equipment Used by Patients in Supine, Prone, or Side-Lying Position
5.2 Transfer Surface Size for Equipment Used by Patients in Supine, Prone, or Side-Lying Position....
-
Mockett DH3/BB Square Door Handle Back to back
DESCRIPTION Traditional square pull design gives a bold striking look on any door type....
-
Architectural Builders Hardware Mfg., Inc. 6000 Series Push/Pull Hospital Latch
The 6000 Series Push/Pull Hospital Latch offers versatility and durability for commercial and institutional settings....
-
Transfer Supports (M301.3.1, M302.3.1, and M305.2)
M301.3.1 and M302.3.1 would require transfer supports to be provided for use with the transfer sides....
-
Section D: Entrances
(§§309.4, 404.2.7) D3 On the pull side of the door, is there at least 18" of clearance provided to the side of the latch?...
-
Figure 308.3.1 Unobstructed Side Reach – Drawing from the U.S. Access Board
-
5.2.1.3 Transfer Surface Size Recommendations for Stretchers (M301)
Transfer Surface Size Recommendations for Stretchers (M301) The Committee recommends a minimum transfer surface size of 28 inches wide by 17 inches deep for stretchers located on both long sides...
-
5.4.4.1 Transfer Support Distance from Transfer Surface Recommendation for Stretchers
surface on the opposite side of the transfer....
-
M301.3 Transfer Supports
Transfer Supports Position • Sub-Committee Recommendation: Located longitudinally within the long side of the of the transfer surface....
-
Clear floor space at Lav
Terry, You should identify the minimum dimensions of the clear floor space at the Lav.
-
5.4.4.1 Transfer Support Distance from Transfer Surface for Stretchers
Transfer supports should be located along the long side of the transfer surface on the opposite side of the transfer....
