About Floor Plates/Safety Treads Pemko can fabricate almost any floor plate threshold you might require. Floor plates are furnished undrilled unless drilling...
Search Results "Level Boarding"
-
PEMKO 2" Floor Plates/Safety Treads No. 190B
-
PEMKO 2" Floor Plates/Safety Treads No. E197
About Floor Plates/Safety Treads Pemko can fabricate almost any floor plate threshold you might require. Floor plates are furnished undrilled unless drilling...
-
PEMKO 3" Floor Plates/Safety Treads No. 200
Pemko manufactures thresholds in several materials to meet customer needs. Extruded Aluminum thresholds are manufactured of tempered aluminum, 6063-T6. Architectural bronze/brass...
-
PEMKO 4" Floor Plates/Safety Treads No. 192
Pemko manufactures thresholds in several materials to meet customer needs. Extruded Aluminum thresholds are manufactured of tempered aluminum, 6063-T6. Architectural bronze/brass...
-
PEMKO 2" to 48" Aluminum Plates No. 18/1
Pemko manufactures thresholds in several materials to meet customer needs. Extruded Aluminum thresholds are manufactured of tempered aluminum, 6063-T6. Architectural bronze/brass...
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
504.4 Tread Surface
Changes in level are not permitted. EXCEPTION: Treads shall be permitted to have a slope not steeper than 1:48. Advisory 504.4 Tread Surface....
-
§ 38.83(c)(3) Ramp threshold
Changes in level between 1/4 inch and 1/2 inch shall be beveled with a slope no greater than 1:2....
-
504.4 Tread Surface
Changes in level are not permitted. EXCEPTION: Treads shall be permitted to have a slope not steeper than 1:48. Advisory 504.4 Tread Surface....
-
F201.4.1 Documentation and Notification When Exceptions Used for Trails and Beach Access Routes
Federal agencies shall notify the Access Board if an entire trail is exempted from complying with 1017 based on Exception 2 in 1017.1, and if a beach access route is not provided based on...
-
§ 38.159(c)(3) Ramp threshold
Changes in level between 1/4 inch (6.5 mm) and 1/2 inch (13 mm) shall be beveled with a slope no greater than 1:2....
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
504.4 Tread Surface
Changes in level are not permitted. EXCEPTION: Treads shall be permitted to have a slope not steeper than 1:48. Advisory 504.4 Tread Surface....
-
7.4.6 Tread Obstacles
Tread obstacles on trails shall not exceed 2 inches (50 mm) in height measured vertically to the highest point. Where the trail surface is paved or is elevated above the natural...
-
A4.28.2 Audible Alarms
Audible emergency signals must have an intensity and frequency that can attract the attention of individuals who have partial hearing loss. People over 60 years of age generally have...
-
A4.28.2 AUDIBLE ALARMS
Audible emergency signals must have an intensity and frequency that can attract the attention of individuals who have partial hearing loss. People over 60 years of age generally have...
-
Wet Conditions [§405.10]
Wet Conditions [§405.10] Landings subject to wet conditions must be designed to prevent the accumulation of water. Landings are permitted slopes not steeper than 1:48 to allow for...
-
Figure 810.2.2 Dimensions of Bus Boarding and Alighting Areas – Drawing from the U.S. Access Board
-
§ 38.25(b) Contrast
All step edges, thresholds and the boarding edge of ramps or lift platforms shall have a band of color(s) running the full width of the step or edge which contrasts from the step tread and...
-
1003.3 Clearances
Clearances at boat slips and on boarding piers at boat launch ramps shall comply with 1003.3. Advisory 1003.3 Clearances....
-
1003.3 Clearances
Clearances at boat slips and on boarding piers at boat launch ramps shall comply with 1003.3. Advisory 1003.3 Clearances....
-
Armor-Tile Tactile Systems Cast In Place Detectable Warning Surface System
Armor-TileTMÂ Cast in Place is the world leader in tactile walking surface indicators systems. Manufactured of a diamond-hard vitrified polymer composite, Armor-TileTMÂ truncated dome...
-
ADA Solutions, Inc. Cast in Place Replaceable Tactile Pavers
Cast in Place Replaceable Tactile, available in both Rectangular and Radius, is made of a colorfast and UV stable homogenous glass and carbon composite with fiberglass truncated...
