Search Results "Grab Bar Clearance"
-
Figure 608.3.3 Grab Bars for Alternate Roll-In Type Showers – Drawing from the U.S. Access Board
-
306.2.4 Additional Clearance
Space extending greater than 6 inches (150 mm) beyond the available knee clearance at 9 inches (230 mm) above the finish floor or ground shall not be considered toe clearance....
-
806.4 Hotel, Motel and Condominium Special Accessibility Features
percent of the guest rooms minus the Total Number of Required (accessible) Rooms required by Table 224.2 shall provide the following additional special accessibility features: (i) Grab...
-
11B-809.10.8.4 Knee and toe clearance
Knee and toe clearance shall be provided and comply with Section 11B-306....
-
11B-809.10.8.4 Knee and toe clearance
Knee and toe clearance shall be provided and comply with Section 11B-306....
-
WET BAR
WET BAR. [DSA-AC] An area or space with a counter equipped with a sink and running water but without cooking facilities....
-
Doorways: ADA Standard Section 405.7.5
Section 405.7.5 covers the current ADA Standards for doorway maneuvering clearance at ramp landings.
-
11B-306.3.5 Width
Knee clearance shall be 30 inches (762 mm) wide minimum....
-
11B-306.2.5 Width
Toe clearance shall be 30 inches (762 mm) wide minimum....
-
11B-306.3.5 Width
Knee clearance shall be 30 inches (762 mm) wide minimum....
-
11B-306.2.5 Width
Toe clearance shall be 30 inches (762 mm) wide minimum....
-
4.3.4 Knee and Toe Clearances
from wall • Toe clearance height: 356 mm (14 in.) minimum , measured from the floor • Knee clearance height: 711 mm (28 in.) minimum, measured from the floor • Knee clearance depth...
-
11B-306.3.2 Maximum depth
Knee clearance shall extend 25 inches (635 mm) maximum under an element at 9 inches (229 mm) above the finish floor or ground....
-
11B-306.3.2 Maximum depth
Knee clearance shall extend 25 inches (635 mm) maximum under an element at 9 inches (229 mm) above the finish floor or ground....
-
7(2) Usable bathrooms
Powder rooms that are subject to the requirements of section 100.205(c)(3)(iv) must have reinforcements for grab bars as provided in the guideline for Requirement 6....
-
11B-306.2.1 General
Space under an element between the finish floor or ground and 9 inches (229 mm) above the finish floor or ground shall be considered toe clearance and shall comply with Section 11B-306.2...
-
11B-306.2.1 General
Space under an element between the finish floor or ground and 9 inches (229 mm) above the finish floor or ground shall be considered toe clearance and shall comply with Section 11B-306.2...
-
11B-407.4.3 Platform to hoistway clearance
The clearance between the car platform sill and the edge of any hoistway landing shall be 1¼ inch (32 mm) maximum....
-
11B-407.4.3 Platform to hoistway clearance
The clearance between the car platform sill and the edge of any hoistway landing shall be 1¼ inch (32 mm) maximum....
-
R405 Knee and Toe Clearance
R405 Knee and Toe Clearance...
-
306 Knee and Toe Clearance
306 Knee and Toe Clearance...
-
11B-804.2 Clearance
Where a pass through kitchen is provided, clearances shall comply with Section 11B-804.2.1. Where a U-shaped kitchen is provided, clearances shall comply with Section 11B-804.2.2....
-
11B-804.2 Clearance
Where a pass through kitchen is provided, clearances shall comply with Section 11B-804.2.1. Where a U-shaped kitchen is provided, clearances shall comply with Section 11B-804.2.2....
