Queues and waiting lines servicing counters or check-out aisles required to comply with Sections 11B-904.3 or 11B-904.4 shall comply with Section 11B-403....
Search Results "Cross-Aisle"
Filters
Commonly Searched Documents
-
11B-227.5 Queues and Waiting Lines
-
221.1 General
Assembly areas shall provide wheelchair spaces, companion seats, and designated aisle seats complying with 221 and 802. In addition, lawn seating shall comply with 221.5....
-
1. Transfer Supports
specifications to the requirements for location (M305.2.1) and length (M305.2.2) based on the type of transfer support required; has added new technical requirements for height (M305.2.3), cross...
-
4.1.3(19)(a)
over 500 6, plus 1 additional space for each total seating capacity increase of 100 In addition, one percent, but not less than one, of all fixed seats shall be aisle...
-
1. Sloped Surfaces
Cross slope is the slope or grade of a surface perpendicular to the running slope. The most cross slope allowed on an accessible route is 1:50 (2% or 1.15 degrees)....
-
11B-406.5.10 Diagonal curb ramps
Diagonal curb ramps with flared sides shall have a segment of curb 24 inches (610 mm) long minimum located on each side of the curb ramp and within the marked crossing....
-
Issue 2: Location relative to the crosswalk
Issue 2: Location relative to the crosswalk An APS that is mounted outside the crosswalk area may provide misleading information about the crossing location....
-
Access Board: Accessible Van Parking
This video is part of a longer animation produced by the U.S. Access Board. View the animation video in it's entirety on the Access Board's website here:...
-
4.1.2(5)(b)
(b) One in every eight accessible spaces, but not less than one, shall be served by an access aisle 96 in (2440 mm) wide minimum and shall be designated “van accessible” as required by 4.6.4...
-
A3
Is the area for the access aisle at least 5-feet wide and 20-feet long? [ADA Standards § 4.6.6]. ...
-
11B-406.5.10 Diagonal curb ramps
Diagonal curb ramps with flared sides shall have a segment of curb 24 inches (610 mm) long minimum located on each side of the curb ramp and within the marked crossing....
-
11B-227.5 Queues and Waiting Lines
Queues and waiting lines servicing counters or check-out aisles required to comply with Sections 11B-904.3 or 11B-904.4 shall comply with Section 11B-403 _|Walking Surfaces|_. ...
-
11B-227.5 Queues and Waiting Lines
Queues and waiting lines servicing counters or check-out aisles required to comply with Sections 11B-904.3 or 11B-904.4 shall comply with Section 11B-403 _|Walking Surfaces|_. ...
-
Boat Slips: ADA Standard Section 1003.2.1
The cross slope specified in 403.3 and 405.3 for gangways, transition plates, and floating piers that are part of accessible routes shall be measured in the static position. 8....
-
11B-1003.2.1 Boat slips
The cross slope specified in Sections 11B-403.3 and 11B-405.3 for gangways, transition plates, and floating piers that are part of accessible routes shall be measured in the static position...
-
Q12: Full-depth Pavement Patching
If the pavement patching impacts the curb at a pedestrian street crossing where no curb ramp exists, the work affecting the curb falls within the definition of “alteration,” and a curb ramp...
-
Arriving at the Polling Place: Parking
Generally, the access aisle must be at least 60 inches wide for cars and 96 inches wide for vans....
-
Issue 3: Which signal? Speech WALK messages necessary
Pedestrians standing at one crosswalk could mistake the message of the other crosswalk for their indication to begin crossing....
-
Built-up Curb Ramps [4.7.6]
Built-up curb ramps are permitted where they do not project into vehicular traffic lanes or access aisles at parking spaces and passenger loading zones....
-
11B-228.3 Electric vehicle charging stations
[See subsections ...]
-
11B-812.9 Surface marking
EVCS vehicle spaces shall provide surface marking stating “EV CHARGING ONLY” in letters 12 inches (305 mm) high minimum. The centerline of the text shall be a maximum of 6 inches...
-
M305.2.4 Cross Section (Section-by-Section Analysis)
with non-circular cross sections to have a cross section dimension of 2 inches maximum, and a perimeter dimension of 4 inches minimum and 4.8 inches maximum....
