At least 25 percent of the railings, guards, or handrails shall be 34 inches (864 mm) maximum above the ground or deck surface....
Search Results "Door Surface"
Commonly Searched Documents
-
11B-1005.2.1 Height
-
11B-411.2.1.6 Identification of floors served
consoles located on floors with a building entry, including parking and transfer levels, shall be provided with signs complying with Sections 11B-703.2, 11B-703.3, and 11B-703.5 on the surface...
-
11B-1005.2.1 Height
At least 25 percent of the railings, guards, or handrails shall be 34 inches (864 mm) maximum above the ground or deck surface....
- Carr Corporation Specimen Pass-through Cabinet: SPT-12
- Rebuilding Together Harrisonburg-Rockingham County - Harrisonburg, VA
- American Foundation for the Blind
- Bradley 20.6 Gallon Waste Receptacle 355
-
Shared Use Paths: ADA Standard Section 2.
address access to sidewalks, streets, and other pedestrian facilities, provide requirements for pedestrian access routes, including specifications for route width, grade, cross slope, surfaces...
-
11B-609.3 Spacing
Section 11B-609.9 the space between the walls and the grab bar shall be 1½ inches (38 mm) minimum for a distance of 6 inches on either side of the inside corner between two adjacent wall surfaces...
- Carr Corporation Narcotics Locker NL10
-
Expert opinion on the current knowledge
None of the research identified described how well individuals are able to overcome physical barriers in between the wheelchair and target surfaces. ...
-
Grab Bars
Grab bars and any wall or other surfaces adjacent to grab bars must have rounded edges and are not allowed to have sharp or abrasive surfaces....
-
11B-705.1.2.3 Islands or cut-through medians
cut-through less 2 inches (51 mm) maximum on each side, placed at the edges of the pedestrian island or cut-through median, and shall be separated by 24 inches (610 mm) minimum of walking surface...
-
11B-406.5.12 Detectable warnings
width of the curb ramp (exclusive of flared sides) and shall extend either the full depth of the curb ramp or 24 inches (610 mm) deep minimum measured from the back of the curb on the ramp surface...
-
M303.2.6 Edge Protection (Section-by-Section Analysis)
Protection), the final rule requires platforms with wheelchair spaces that are raised more than 1½ inches in height to provide a minimum 2-inch-high edge protection, measured from the surface...
-
Maximum Slope at Ground Level
A berm may be a natural sloped surface that is present in a hilly play area site, or a ground-level route built with slopes....
-
606.3 Height
Lavatories and sinks shall be installed with the front of the higher of the rim or counter surface 34 inches (865 mm) maximum above the finish floor or ground. EXCEPTIONS: 1....
-
Amusement Ride Seats Designed for Transfer
When greater distances are required for transfer, consideration should be given to providing gripping surfaces, seat paddings, and avoiding sharp or protruding objects....
-
1007.3.2 Golf Club Reach Range Area
This includes accessible routes provided adjacent to or, where provided, on the playing surface of the hole....
-
Tent Pads and Tent Platforms [1013]
Tent pads and tent platforms are defined spaces with prepared surfaces for setting up and securing tents....
-
Curb Ramps and Blended Transitions (R309.4) (Section-by-Section Analysis)
Detectable warning surfaces are not required on curb ramps and blended transitions that connect the access aisle to the sidewalk, including where the sidewalk is at the same level as the...
-
F. Check-In Areas
If a permanent reception counter is used for check in, make sure to provide a writing surface at an accessible height for people who use a wheelchair, scooter, or other mobility device....
-
4.6.1 General
In alterations, where a condition for exception in section 1.1 prohibits full compliance with a specific requirement for clear floor or ground space surface, slope, size, or location, the...
-
2. Referenced Documents
Guide for Conducting Subjective Pavement Ride Quality Ratings E2133 Standard Test Method for Using a Rolling Inclinometer to Measure Longitudinal and Transverse Profiles of a Traveled Surface...