The height of the lift seat shall be designed to allow a stop at 16 inches (405 mm) minimum to 19 inches (485 mm) maximum measured from the deck to the top of the seat surface when in the...
Search Results "Transfer Surface Height"
-
1009.2.4 Seat Height
-
11B-1008.3.2.4 Contrasting stripe
Striping complying with Section 11B-504.4.1 shall be provided at each transfer step....
-
11B-1008.3.2.4 Contrasting stripe
Striping complying with Section 11B-504.4.1 shall be provided at each transfer step....
-
Surface Smoothness
The standards limit changes in level and openings in floor and ground surfaces, but they do not further address overall surface smoothness....
-
1014.2.1 Transfer Access
The surface of the clear ground space is required to be firm and stable, and to slope not steeper than 1:48 in any direction....
-
M301.2.3 Size (Section-by-Section Analysis)
As discussed in Section IV.B.1.c (Significant Changes – Transfer Surface Size), in the final rule the Access Board has revised this provision to account for the two types of transfer surfaces...
-
11B-813.2.1.3 Height and operation
Adult changing table height shall be adjustable from 17 inches (432 mm) above the floor or ground to 38 inches (965 mm) above the floor or ground, as measured to the top of the changing...
-
Studies of Wheeled Mobility Devices and Transferring Abilities
The safest and most easily accessible transfers are those with no or very little horizontal and vertical distance between the seat of the wheelchair and the transfer surface....
-
Preferred Seat Widths
The seat width percentiles remained the same for transfers to and from the station and within each protocol....
-
Additional Technical Criteria Considered for Transfer Supports
As discussed below, the Access Board is considering whether additional technical criteria would be appropriate for transfer supports....
-
5.4.7 Transfer Support Gripping Surface Clearance for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.7 Transfer Support Gripping Surface Clearance for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
Diversified Woodcrafts Oak Table with Book Compartments 24x48
Warranty Made in the USA Manufactured with 2 book compartments measuring 14"W x 13-5/8"D x 3-7/8"H Minimal assembly required; legs need to be attached No Table Surface...
-
Populas Infinity Workstation
Each mode allows quick, smooth height adjustment without intruding into leg and foot clearance spaces when not in use....
-
(5) Bricks and Mortar Transfers
(5) Bricks and Mortar Transfers: A transfer of interest in the Brand Hotel in which, after completion of the transaction, the pre-transfer hotel owner retains management control of hotel...
-
M301.2.3 Size
The size of the transfer surface shall comply with M301.2.3.1 or M301.2.3.2. The size of transfer surfaces shall be measured from center points of their opposing sides....
-
1009.2.4 Seat Height
The height of the lift seat shall be designed to allow a stop at 16 inches (405 mm) minimum to 19 inches (485 mm) maximum measured from the deck to the top of the seat surface when in the...
-
7. Seat Transfer
Are the roll-in showers free of doors that would impede wheelchair transfer onto the seat? [ADA Stds. 4.21.8] Yes __ No __ N/A __ Comments: _______________________________________...
-
Transfer Entry
Transfer Entry There is a large amount of variance in amusement rides and the sides of the ride are often part of the restraint or securement system....
-
606.3 Height
606.3 Height. Lavatories and sinks shall be installed with the front of the higher of the rim or counter surface 34 inches (865 mm) maximum above the finish floor or ground....
-
11B-411.4.2 Floor surfaces
Floor surfaces in elevator cars shall comply with Section 11B-407.4.2....
-
11B-411.4.2 Floor surfaces
Floor surfaces in elevator cars shall comply with Section 11B-407.4.2....
-
(1) Intra-Family Transfers
(1) Intra-Family Transfers: A transfer of interest in a Brand Hotel to or for the benefit of an immediate family member;...
-
11B-409.4.2 Floor surfaces
Floor surfaces in elevator cars shall comply with Sections 11B-302 and 11B-303....
-
11B-409.4.2 Floor surfaces
Floor surfaces in elevator cars shall comply with Sections 11B-302 and 11B-303....
