Where knee clearance is required under an element as part of a clear space, the knee clearance shall be 280 mm (11 in) deep minimum at 230 mm (9 in) above the finish surface, and 205 mm...
Search Results "9-1-1 Service"
Filters
Commonly Searched Documents
-
R405.3.3 Minimum Required Depth
-
§104.41 Application of this subpart.
[45 FR 30936, May 9, 1980, as amended at 65 FR 68055, Nov. 13, 2000]...
-
11B-215.4 Transient lodging
Guest rooms required to comply with Section 11B-224.4 shall provide fire alarms complying with Chapter 9, Section 907.5.2.3.2, and carbon monoxide alarms, where provided, complying with...
-
610.3.1 Rectangular Seats
The side edge of the seat shall be 1½ inches (38 mm) maximum from the adjacent wall. Figure 610.3.1 Rectangular Shower Seat...
-
11B-407.4.8.2.1 Signal type
Exception: For elevators that have a rated speed of 200 feet per minute (1 m/s) or less, a non-verbal audible signal with a frequency of 1500 Hz maximum which sounds as the car passes or...
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
204.1 General
EXCEPTIONS: 1. Within areas of sport activity, protruding objects on circulation paths shall not be required to comply with 307. 2....
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the transfer...
-
1011.2.4 Openings
Openings in the clear ground space surface shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1011.2.4 Openings. ...
-
M303.3.2 Beveled (Section-by-Section Analysis)
with a change in level at the entry to the wheelchair space, level changes greater than ¼ inch but not greater than ½ inch would be required to be beveled with a slope not steeper than 1:...
-
F206.2.6 Performance Areas
An accessible route shall be provided from performance areas to ancillary areas or facilities used by performers unless exempted by F206.2.3 Exceptions 1 through 6....
-
Recommendations
Recommendations Based on the data in Table 1 and the observations above, we recommend: a minimum flat surface of 40 in. length for platforms accommodating wheeled mobility devices...
-
206.6 Elevators
EXCEPTIONS: 1....
-
F206.6 Elevators
EXCEPTIONS: 1....
-
§27.129(f)(3)
The applicant or recipient is restored to eligibility if it demonstrates to the satisfaction of the Secretary at the hearing that it satisfied the requirements of paragraph (f)(1) of this...
-
§ 36.304(d)(5) Qualified small business
has met its obligation to remove architectural barriers where readily achievable for a given year if, during that tax year, the entity has spent an amount equal to at least one percent (1%...
-
E101.1 Purpose
These Revised 508 Standards, which consist of 508 Chapters 1 and 2 (Appendix A), along with Chapters 3 through 7 (Appendix C), contain scoping and technical requirements for information...
-
407.2.1.5 Signals
EXCEPTIONS: 1....
-
You must provide timely enplaning, deplaning, and connecting assistance
[Secs. 382.39(a)(1) and 382.39(b)(5)]...
-
CARRIAGE UNIT
[HCD 1-AC] A dwelling unit with living space on one or more floors immediately above a Group U, private garage or garages....
-
504.4 Tread Surface
EXCEPTION: Treads shall be permitted to have a slope not steeper than 1:48. Advisory 504.4 Tread Surface....
-
4.4.2 Head Room
clearance of an area adjoining an accessible route is reduced to less than 80 in (nominal dimension), a barrier to warn blind or visually-impaired persons shall be provided (see Fig. 8(c−1)...
-
703.2.5 Character Height
EXCEPTION: Where separate raised and visual characters with the same information are provided, raised character height shall be permitted to be 1/2 inch (13 mm) minimum....
-
2.4 Do Your Research and Offer Suggestions
(See Resources at the end of section 1) Have this information ready to share with the facility’s staff....