It references dimensions of clearance height and depth to the forward-most abdomen point on a person....
Search Results "Adult Dimension"
Filters
Commonly Searched Documents
-
Knee Clearance: Clearance as Measured from Anterior-Most Abdomen Point - Manual Wheelchair
-
11B-703.6.1 Pictogram field
The 6-inch vertical dimension applies to the field, not the symbol. The symbol may be smaller than the field....
-
505.4 Height
The requirements for stair and ramp handrails in this document are for adults....
-
Introduction
Event organizers will find that when these elements are accessible, they serve not only the participants with disabilities but also a wide range of others, including older adults, baby boomers...
-
Including Customers with Disabilities in the Process
ways to work around physical barriers and product inaccessibility, can offer ideas and innovative solutions to attract and keep new customers, especially those in the burgeoning older adult...
-
232.2 General Holding Cells and General Housing Cells
., male/female and adult/juvenile) to facilitate access....
-
505.4 Height
The requirements for stair and ramp handrails in this document are for adults....
-
11B-505.4 Height
The requirements for stair and ramp handrails in this document are for adults....
-
4.20.2 Floor Space
However, because frail older adults do not perform sliding transfers, clear floor space in eldercare facilities was needed for one or more caregivers to be able to assist with getting in...
-
11B-903.4 Back support
The bench shall provide for back support or shall be affixed to a wall along its long dimension....
-
Appendix: Revised Annotated Bibliography
Dimensions given in this report include 132 standard measurements, 60 derived dimensions, and 48 head and face dimensions reported in traditional linear terms but collected by means of an...
-
AssistiveWare Keeble Accessible Keyboard
Accessible keyboard for iOS Keeble allows students and adults with physical or vision impairments to type in almost any app....
-
Background
For example, Sanford, et al. have previously reported (1995, 1999) that the preferred ADA toilet configuration does not work as well as it should for the majority of older adults, including...
-
11B-703.6.1 Pictogram field
The 6-inch vertical dimension applies to the field, not the symbol. The symbol may be smaller than the field....
-
11B-407.4.7.2 Keypads
The dot shall be 0.118 inch (3 mm) to 0.120 inch (3.05 mm) base diameter and in other aspects comply with Table 11B-703.3.1 _|Braille Dimensions|_....
-
11B-302.3 Openings
Elongated openings shall be placed so that the long dimension is perpendicular to the dominant direction of travel....
-
1. Measuring Tape
You will generally not need to measure dimensions in increments of less than ¼ inch....
-
5.4.2.1 Transfer Support Length Recommendation for Stretchers
5.4.2.1 Transfer Support Length Recommendation for Stretchers On Stretchers, the transfer surface is oriented along the long dimension of the surface on which patients are positioned...
-
5.4.4.2 Transfer Support Distance from Transfer Surface Recommendation for Imaging Equipment
Rationale for the Recommendation The Committee decided to follow the recommended 1 1/2inch proposal but included a 3-inch dimension to accommodate movement of the support....
-
Openings in Beach Access Routes
Place elongated openings more than a quarter of an inch wide with the long dimension perpendicular or diagonal to the primary direction of travel (see figure 44)....
-
Openings in Outdoor Recreation Access Route Surfaces
Place elongated openings that are more than a quarter of an inch wide with the long dimension perpendicular or diagonal to the primary direction of travel (figure 44)....
-
Knee Clearance: Clearance as Measured from Anterior-Most Point - Manual Wheelchair
It references dimensions of clearance height and depth to the forward-most point on the person or mobility device (e.g., toe, footrest)....
-
Knee Clearance: Clearance as Measured from Dorsal Foot Point - Manual Wheelchair
It references dimensions of clearance height and depth to the dorsal foot point on a person (e.g., top of ankle)....
-
1.2.1
1.2.1 Use the plus - or - minus symbol (±) after a dimension when it must be made clear what the expected tolerance is. This should be coordinated with the specification requirements....
