The placement of detectable warning surfaces shall comply with R305.2. Advisory R305.2 Placement. Some detectable warning products require a concrete border for proper installation....
Search Results "Transfer Surface Height"
-
R305.2 Placement
-
Seating [4.32.2] and Knee Clearance [4.32.3]
The over-the-surface reach is limited to 25 inches if at least this much space is available below for knees and toes; (the forward seated reach may not extend beyond the toes)....
-
1018.10 Dune Crossings
The curbs or barriers are required to prevent the passage of a 2 inch diameter sphere, where any portion of the sphere is within 2 inches of the crossing surface....
-
§ 38.119(b)
doorways of cars not operating at lighted station platforms shall have outside lights which, when the door is open, provide at least 1 foot-candle of illumination on the station platform surface...
-
§ 38.81(c)
(c) The doorways of vehicles not operating at lighted station platforms shall have outside lights which provide at least 1 foot-candle of illumination on the station platform or street surface...
-
11B-407.4.6.2.1 Size and shape
Buttons shall have square shoulders, be ¾ inch (19.1 mm) minimum in their smallest dimension and be raised 1/8 inch (3.2 mm) plus or minus 1/32 inch (0.8 mm) above the surrounding surface...
-
Water Closet Clear Floor Space in Toilet Compartments
Locating lavatories outside the specified water closet clearance allows more options in the approach and transfer to water closets....
-
ENFORCEMENT
In the event that Camp Bravo seeks to sell, transfer, or assign all or part of its interest during the term of this Agreement, as a condition of sale, transfer, or assignment, Camp Bravo...
-
23. How should an employer handle requests for modified or part-time schedules for an employee covered by both the ADA and the Family and Medical Leave Act (FMLA)?
When such leave is foreseeable based on planned medical treatment, an employer may require the employee to temporarily transfer (for the duration of the leave) to an available alternative...
-
OTHER PROVISIONS
In the event that Aurora seeks to sell, transfer, or assign all or part of its interest during the term of this Agreement, as a condition of sale, transfer, or assignment, Aurora will obtain...
-
OTHER PROVISIONS
In the event that Genesis seeks to sell, transfer, or assign substantially all of its assets or a controlling membership position in Genesis during the term of this Agreement, then, as a...
-
382.61 What are the requirements for movable aisle armrests?
submit an equivalent alternative request concerning movable armrests must show the Department that, in fact, persons with mobility impairments using aisle and boarding wheelchairs can transfer...
-
11B-224.2.2 More than fifty guest room facilities
ETA considers the ADA requirement for rooms without roll-in showers to be a recognition that some individuals with mobility impairments actually prefer an accessible bathtub or transfer-type...
-
Re: When is a Curb Ramp a Ramp?
Curb height say 6'' The lowest slope for a ramp would be 5.1% or just under 1:20 So if the walkway was shorter than 10' I think it could be called a curb ramp and would only require...
- AccessaBath Shower Systems
- Greenfields Outdoor Fitness Accessible Reverse Butterfly GR2005-1-90-W
- Greenfields Outdoor Fitness Accessible Butterfly GR2005-1-08-W
-
III-6.1000 General
It includes remodeling, renovation, rearrangements in structural parts, and changes or rearrangement of walls and full-height partitions....
-
Knee and Toe Clearance (M303.2.4)
inches deep minimum at 27 inches above the floor Between 9 inches and 27 inches above the floor, knee clearance is permitted to reduce at rate of 1 inch in depth for every 6 inches in height...
- AquaTrek2 ADA Ladder System
- Ramp NOW Alumiramp Modular Ramps
- AccessRec De-Bug All Terrain Wheelchair
-
Dispersion: ADA Standard Section 233.3.5
Section 233.3.5 covers scoping requirements in the current ADA Standards for dispersion of individual residential dwelling units.
-
Industry Standards
Test Method for Determining Floor Tolerances Using Waviness, Wheel Path and Levelness Criteria (Metric) ASTM F 802-83(2003) Standard Guide for Selection of Certain Walkway Surfaces...