Different types of lockers may include full-size and half-size lockers, as well as those specifically designed for storage of various sports equipment....
Search Results "Designated Aisle Seat (Assembly)"
Filters
Commonly Searched Documents
-
11B-225.2.1 Lockers
-
11B-225.2.1 Lockers
Different types of lockers may include full-size and half-size lockers, as well as those specifically designed for storage of various sports equipment. ◼...
-
M301.3.1 Transfer Supports
It will be located at the designated transfer location....
-
3. Discussion of Comments on Related Fair Housing Issues Compliance Deadline
Section 100.205 of the Fair Housing regulations incorporates the Act's design and construction requirements, including the requirement that multifamily dwellings for first occupancy after...
-
Definition of "wheelchair.'' (Section-by-Section Analysis)
The NPRM defined a wheelchair as ‘‘a device designed solely for use by an individual with a mobility impairment for the primary purpose of locomotion in typical indoor and outdoor pedestrian...
-
5.1 Architectural Barriers Act (ABA).
following ABA requirements apply to recipients of federal financial assistance from DOT: 5.1.1 ATBCB Final Rule, 36 CFR part 1190, Minimum Guidelines and Requirements for Accessible Design...
-
1.4 Overview of Report
However, as is clear throughout the report, with some important exceptions, current equipment designs rarely accommodate fully persons with disabilities....
-
Categorization of wheelchair versus other power-driven mobility devices. (Section-by-Section Analysis)
size to be too restrictive, the vast majority of advocacy, nonprofit, and individual commenters opposed using the Department of Transportation's definition of ‘‘common wheelchair'' to designate...
-
11B-104.1.1 Construction and manufacturing tolerances
Recognized tolerances are not intended to apply to design work. It is good practice when specifying dimensions to avoid specifying a tolerance where dimensions are absolute....
-
M301.2.2 Transfer Surface Size
inches wide minimum and 21 inches deep minimum and is located such that the long dimension of 28 inches is be located parallel to the patient scanning/imaging table side at a location designated...
-
4.3.1 Overview of Imaging Equipment and Regulatory Environment
Generally, this equipment is permanently mounted in a fixed installation within specially designed spaces that must perform specific essential functions, including supporting heavy weight...
-
ADA Requirements
Under the ADA, hotels, motels, inns and other places of lodging designed or constructed after January 26, 1993, must be usable by persons with disabilities....
-
Re: Angled Parking
Requires the Accessibility Specialist plan or above. (Login or upgrade your account!)
-
E. EXPERT TESTIMONY
Steinfeld is a professor of architecture, the Director of the Center for Inclusive Design and Environmental Access ("IDEA Center"), and an advocate for improved disability access standards...
-
Introduction
FSORAG and FSTAG look much the same as they did before revision and are still individual documents that integrate universal design, as well as agency terminology and processes....
-
215 Fire Alarm Systems
1991 Standards for Accessible Design 2010 Standards for Accessible Design What’s New/Different 4.28.1 General....
-
Section 1194.26 Desktop and Portable Computers (Preamble, Section-by-Section Analysis)
In contrast, the provisions in this section address physical characteristics of computer systems including the design of controls and the use of connectors....
-
Amusement rides
Section 234 of the 2010 Standards provides accessibility guidelines for newly designed and constructed amusement rides....
-
General
Like many other facilities designed to be accessible, accessible toilet facilities can and do serve a wide range of individuals with and without disabilities....
-
Fact Sheet: Highlights of the Final Rule to Amend the Department of Justice's Regulation Implementing Title III of the ADA
The ADA requires the Department to publish ADA design standards that are consistent with the minimum guidelines published by the U.S....
-
Public Rights-of-Way
These comments addressed roadway design, speed bumps, crosswalks, on-street parking, audible signs and pedestrian signals, and emergency call boxes....
-
Accessible Gates for Trails and Roads
jgroenier@fs.fed.us Accessible Gates for Trails and Roads James "Scott" Groenier, Project Leader The Missoula Technology and Development Center (MTDC) has reviewed available gate designs...
-
"Existing Facility" (Section-by-Section Analysis)
Under the ADA, a facility is initially classified as one of three types: (1) An existing facility; (2) an altered facility; or (3) a newly designed and constructed facility. ...
-
C.3.i. - Does Section 508 require contractors to manufacture EIT that meets the applicable Access Board’s technical provisions?
By doing so, Section 508 provides an incentive for EIT manufacturers and designers to ensure that their products are usable by everyone – including people with disabilities....