Function key surfaces must have tactile symbols as follows: Enter or Proceed key: raised circle; Clear or Correct key: raised left arrow; Cancel key: raised letter ex; Add Value key: raised...
Search Results "Extended Floor Surface"
Filters
Commonly Searched Documents
-
§27.71(k)(6)(iv)(B) Tactile symbols.
-
T402.7 Edge Guards
Edge guards shall be 2 inches (51 mm) high minimum above the ramp or bridgeplate surface....
-
§ 27.71(k)(6)(iv)(B) Tactile symbols
Function key surfaces must have tactile symbols as follows: Enter or Proceed key: raised circle; Clear or Correct key: raised left arrow; Cancel key: raised letter ex; Add Value key: raised...
-
§ 382.57(c)(6)(iv)(B) Tactile symbols
Function key surfaces must have tactile symbols as follows: Enter or Proceed key: raised circle; Clear or Correct key: raised left arrow; Cancel key: raised letter ex; Add Value key: raised...
-
Bus boarding and alighting areas
Bus boarding and alighting areas must be in compliance with the ADA-ABA Guidelines (Section 810.2), which address surfaces (sturdy), dimensions (96" long x 60" wide); connection to sidewalks...
-
1009.2.2 Seat Location
The deck surface between the centerline of the seat and the pool edge shall have a slope not steeper than 1:48. Figure 1009.2.2 Pool Lift Seat Location...
-
707.6.3.2 Tactile Symbols
Function key surfaces shall have tactile symbols as follows: Enter or Proceed key: raised circle; Clear or Correct key: raised left arrow; Cancel key: raised letter ex; Add Value key: raised...
-
705.1.1 Dome Size
Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (23 mm) minimum and 1.4 inches (36 mm) maximum, a top diameter of 50 percent of the base diameter minimum...
-
4.7.2 Slope
Maximum slopes of adjoining gutters, road surface immediately adjacent to the curb ramp, or accessible route shall not exceed 1:20....
-
11B-227.5 Queues and Waiting Lines
Queues and waiting lines servicing counters or check-out aisles required to comply with Sections 11B-904.3 or 11B-904.4 shall comply with Section 11B-403 _|Walking Surfaces|_. ...
-
References
Standard specification for impact attenuation of surface systems under and around playground equipment. ASTM F1292‒99/04, 15.07. ...
-
Significant alternatives which minimize any significant economic impacts on small entities
analyzes the following four requirements in the proposed guidelines that will have more than minimal impacts on state and local transportation departments: Detectable warning surfaces...
-
4.3.2 Seat Height
4.3.2 Seat Height Seat height is an important dimension for establishing the height of built-in seating, toilet heights, tub heights, shower seat heights and other transfer related surfaces...
-
Characteristics of Study Participants
of community mobility is related to the “accessibility” of outdoor surfaces....
-
4.3.8 Operating forces
Broader handles and larger gripping surface areas facilitate stronger grips....
-
The Challenges EV Charging for People with Disabilities
The user extends the cable to the required length (up to 18 feet) and plugs it into the vehicle....
-
The Seeing Eye
To provide ongoing assistance to our graduates and their dogs in order to extend the life of each partnership....
-
Vanity Counter Space
Comparable vanity countertop space need not be one continuous surface and need not be exactly the same size as the countertops in comparable guest bathrooms....
-
4. COMMON PATH OF TRAVEL ITEMS
serving the area of alteration • Public telephones serving the area of alteration • Exterior or interior signs along the path of travel • Accessible route components • Walking surfaces...
-
1003.2.12.2 Opening limitations
From a height of 34 inches (864 mm) to 42 inches (1067 mm) above the adjacent walking surfaces, a sphere 8 inches (203 mm) in diameter shall not pass....
-
Elevated Dune Crossings
Locate handrails continuously along both sides of the dune crossing at a height of 34 inches (865 millimeters) to 38 inches (965 millimeters) above the walking surface....
-
§ 38.77(b)
Handrails shall have a cross-sectional diameter between 11/4 inches and 11/2 inches or shall provide an equivalent grasping surface, and have eased edges with corner radii of not less than...
-
§ 38.155(a)
Handrails shall have a cross-sectional diameter between 11/4 inches and 11/2 inches or shall provide an equivalent grasping surface, and have eased edges with corner radii of not less than...
-
11B-705.1.1.2 Dome spacing
Truncated domes in a detectable warning surface shall have a center-to-center spacing of 2.3 inches (58 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch...
