Loose Fill Surfaces. The predominant surface characteristic is one where many loose particles are combined to create the surface system. ...
Search Results "Fire-Building Surface"
-
Loose Fill Surfaces
-
F233.4.4.1 Alterations to Vacated Buildings
Where a building is vacated for the purposes of alteration and the altered building contains more than 15 residential dwelling units, at least 5 percent of the residential dwelling units...
-
11B-1005.2.1 Height
At least 25 percent of the railings, guards, or handrails shall be 34 inches (864 mm) maximum above the ground or deck surface....
-
11B-1005.2.1 Height
At least 25 percent of the railings, guards, or handrails shall be 34 inches (864 mm) maximum above the ground or deck surface....
-
11B-902.1 General
Dining surfaces and work surfaces shall comply with Sections 11B-902.2 and 11B-902.3....
-
11B-902.1 General
Dining surfaces and work surfaces shall comply with Sections 11B-902.2 and 11B-902.3....
-
11B-302 FLOOR OR GROUND SURFACES
[See subsections ...]
-
Common Questions (Floor and Ground Surfaces)
Common Questions
-
11B-302 Floor or ground surfaces.
[See subsections ...]
-
11B-302 Floor or ground surfaces
[See subsections ...]
-
Performance for Surface Firmness and Stability
Performance for Surface Firmness and Stability In addition to the visual inspection and calculation of the surface deficiency score, the firmness and stability of the surfaces were measured...
-
Stability or Stable Surface
Stability or Stable Surface. ...
-
13. Do the provisions for openings in floor and ground surfaces in Section 302.3 apply to walking surfaces in play areas?
Do the provisions for openings in floor and ground surfaces in Section 302.3 apply to walking surfaces in play areas? Yes....
-
702.1 General
Fire alarm systems shall have permanently installed audible and visible alarms complying with NFPA 72 (1999 or 2002 edition) (incorporated by reference, see “Referenced Standards” in Chapter...
-
Vertical Surface Discontinuities
Vertical Surface Discontinuities. Vertical differences in level between two adjacent surfaces....
-
11B-809.9.4 Work surfaces
Work surfaces shall be 36 inches (914 mm) maximum above the finish floor with minimum lengths at the following locations as required by this section: Linear length of 30 inches...
-
11B-809.9.4 Work surfaces
Work surfaces shall be 36 inches (914 mm) maximum above the finish floor with minimum lengths at the following locations as required by this section: Linear length of 30 inches...
-
404.2.4.4 Floor or Ground Surface
Floor or ground surface within required maneuvering clearances shall comply with 302. Changes in level are not permitted. EXCEPTIONS: 1....
-
404.2.4.4 Floor or Ground Surface
Floor or ground surface within required maneuvering clearances shall comply with 302. Changes in level are not permitted. EXCEPTIONS: 1....
-
407.4.2 Floor Surfaces
407.4.2 Floor Surfaces. Floor surfaces in elevator cars shall comply with 302 and 303....
-
Cross Slope and Surfaces [4.8.6]
Ramp surfaces must comply with requirements for ground and floor surfaces and be "stable, firm, and slip-resistant." A specific level of slip-resistance is not mandated....
-
IV. Discussion of Findings and Implications
of surface maintenance to assure accessibility and safety for use by children on a daily basis. ...
-
§100.205(e)(2)(vi) 2006 International Building Code
(vi) 2006 International Building Code; published by ICC, January 2006, with the January 31, 2007, erratum to correct the text missing from Section 1107.7.5, if adopted without modification...
-
5.2.1.2 Transfer Surface Depth Recommendation for M301
5.2.1.2 Transfer Surface Depth Recommendation for M301 The Committee recommends a minimum transfer surface depth of 17 inches for all M301 except imaging equipment....