The Department is retaining language from former §10.3.1(1), which provides that “Elements such as ramps, elevators, or other circulation devices, fare vending or other ticketing areas,...
Search Results "Employee Work Area"
2010 ADA Definition
Employee Work Area: All or any portion of a space used only by employees and used only for work. Corridors, toilet rooms, kitchenettes and break rooms are not employee work areas.
-
Section 206.3
-
11B-405.7.5 Doorways
Where doorways are located adjacent to a ramp landing, maneuvering clearances required by Sections 11B-404.2.4 and 11B-404.3.2 shall be permitted to overlap the required landing area....
-
SmartCells Flooring: Softer Anti-Fatigue Mats are NOT Better
Research on anti fatigue matting has shown that an optimized anti fatigue surface requires a number of elements to work together....
-
11B-216.13.3 Conditions of use
Deodorizers or Fragrance Emission Devices and Systems (FEDS) shall not be used in the designated area....
-
Newly Constructed Tabled Intersections That Contain Pedestrian Street Crossings With Yield or Stop Control (Section-by-Section Analysis)
In new construction, street intersections in hilly urban areas are typically cut-and filled to produce relative flat or tabled intersections....
-
Tread Obstacles on Outdoor Recreation Access Routes
Sometimes, an alteration project at an existing recreation site includes an area where stairs can't be avoided....
-
SIDEWALKS
Unless already provided, within three years of the effective date of this Agreement, the City of Waukegan will provide curb ramps or other sloped areas complying with the Standards or UFAS...
-
ACCESSIBILITY
[DSA-AC & HCD 1-AC] Accessibility is the combination of various elements in a building, facility, site, or area, or portion thereof which allows access, circulation and the full use...
-
WHAT HAS CHANGED THE MOST?
At least two areas in the revised regulations merit attention from cultural arts administrators: Policies, Procedures, and Practices Service animals Mobility...
-
12143(c)(8)(A)
section identify in the plan any person or other public entity which is providing a paratransit or other special transportation service for individuals with disabilities in the service area...
-
§ 36.403(g)(1)
(1) When the cost of alterations necessary to make the path of travel to the altered area fully accessible is disproportionate to the cost of the overall alteration, the path of travel shall...
-
Sec.36.403(g)(1)
(1) When the cost of alterations necessary to make the path of travel to the altered area fully accessible is disproportionate to the cost of the overall alteration, the path of travel shall...
-
4.1.6(3)(c)(ii)
or technical infeasibility prohibits strict compliance with 4.10.9, the minimum car plan dimensions may be reduced by the minimum amount necessary, but in no case shall the inside car area...
-
DWELLING UNIT
A single unit of residence which provides a kitchen or food preparation area, in addition to rooms and spaces for living, bathing, sleeping, and the like....
-
4.7.11 ISLANDS
Any raised islands in crossings shall be cut through level with the street or have curb ramps at both sides and a level area at least 48 in (1220 mm) long in the part of the island intersected...
-
Can handrails overlap ramp landings?
This also applies to landings required to be at least 60” by 60” where ramps change directions so that the minimum landing area remains clear....
-
68.101(c)(5)(F) Drinking fountains
(F) If drinking fountains are required by the lease agreement, or are provided to serve the leased area, at least one fountain shall comply with TAS 602....
-
11B-205.1 General
In residential dwelling units with mobility features where receptacles are provided in a kitchen at a corner work surface, one receptacle shall be located 36 inches (915 mm) from either...
-
11B-205.1 General
In residential dwelling units with mobility features where receptacles are provided in a kitchen at a corner work surface, one receptacle shall be located 36 inches (915 mm) from either...
-
11B-104.1.1 Construction and manufacturing tolerances
Recognized tolerances are not intended to apply to design work. It is good practice when specifying dimensions to avoid specifying a tolerance where dimensions are absolute....
-
11B-104.1.1 Construction and manufacturing tolerances
Recognized tolerances are not intended to apply to design work. It is good practice when specifying dimensions to avoid specifying a tolerance where dimensions are absolute....
-
105 Referenced Standards
Mechanical Engineers (ASME) for various elevators and platform lifts (105.2.2) American Society for Testing and Materials (ASTM) for use zones, play equipment, and accessible surfaces at play areas...
-
R305 Detectable Warning Surfaces (Section-by-Section Analysis)
At boarding platforms for buses and rail vehicles, detectable warning surfaces must extend the full length of the public use areas of the platform....
