definitions should be based on how the device is defined by manufacturer as follows: Manufacturers design examination tables with primary functions of supporting patients in a prone position, side-lying...
Search Results "Side Transfer Surface"
Filters
Commonly Searched Documents
-
Introduction
-
§27.127(e)(2)
All documents and other evidence offered or taken for the record are open to examination by the parties and opportunity is given to refute facts and arguments advanced by either side....
-
38. Is an employer relieved of its obligation to provide reasonable accommodation for an employee with a disability who fails to take medication, to obtain medical treatment, or to use an assistive device (such as a hearing aid)?
There are many reasons why a person would choose to forgo treatment, including expense and serious side effects....
-
Height [4.27.3]
Height [4.27.3] The operable portions of controls and operating mechanisms must be within established reach ranges for either a forward or side reach as required in 4.2.5 and 4.2.6 (see...
-
A4.2.1(1) Space Requirements for Wheelchairs
For most situations, the addition of an inch of leeway on either side is sufficient. Thus, a minimum clear width of 32 in (815 mm) will provide adequate clearance....
-
A4.2.1(1) Space Requirements for Wheelchairs
For most situations, the addition of an inch of leeway on either side is sufficient. Thus, a minimum clear width of 32 in (815 mm) will provide adequate clearance....
-
C2-1. Objects on sidewalks
Placing an object, like this sign, under the box provides a way to warn the person before they walk into the side of the box....
-
Door Hardware [4.13.9]
When sliding doors are fully open, the hardware must be exposed and usable from both sides....
-
705.1.2 Dome Spacing
Truncated domes in a detectable warning surface shall have a center-to-center spacing of 1.6 inches (41 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch...
-
Seat Height
Seat Height The lift must be designed so that the seat will make a stop between a minimum of 16 inches and maximum of 19 inches (measured from the deck to the top of the seat surface,...
-
11B-505.10.1 Top and bottom extension at ramps
Extensions shall return to a wall, guard, or the landing surface, or shall be continuous to the handrail of an adjacent ramp run....
-
4.7.2 SLOPE
Maximum slopes of adjoining gutters, road surface immediately adjacent to the curb ramp, or accessible route shall not exceed 1.20....
-
4.1.1 General
In alterations, where a condition for exception in section 1.1 prohibits full compliance with a specific requirement for clear floor or ground space surface slope, size, or location, the...
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
13) Detectable warnings
Must be a textured surface on the door handle or hardware (§4.29)....
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
11B-503.3.3 Marking
The area within the borderlines shall be marked with hatched lines a maximum of 36 inches (914 mm) on center in a color contrasting with that of the aisle surface....
-
AccessaBath Shower Systems
includes wall enclosure, shower pan, flexible threshold, seat, grab bars, mixing valve and trim and adjustable shower wand AccessaBath Shower Systems: Wheel Chair Access and Wheel Chair Transfer...
-
Greenfields Outdoor Fitness Accessible Reverse Butterfly GR2005-1-90-W
Patent 9,079,069) units allow users to exercise without having to transfer out of their wheelchairs....
-
Greenfields Outdoor Fitness Accessible Butterfly GR2005-1-08-W
Patent 9,079,069) units allow users to exercise without having to transfer out of their wheelchairs....
-
Toilet Compartment Access
(still swinging outward) and the approach is from the opposite side. ...
-
11B-407.4.6.2.1 Size and shape
Buttons shall have square shoulders, be ¾ inch (19.1 mm) minimum in their smallest dimension and be raised 1/8 inch (3.2 mm) plus or minus 1/32 inch (0.8 mm) above the surrounding surface...
-
§382.57(c)(6)(iv)(B) Tactile symbols
Function key surfaces must have tactile symbols as follows: Enter or Proceed key: raised circle; Clear or Correct key: raised left arrow; Cancel key: raised letter ex; Add Value key: raised...
-
505.10.3 Bottom Extension at Stairs
Extension shall return to a wall, guard, or the landing surface, or shall be continuous to the handrail of an adjacent stair flight....
