On over-the-road-buses, doorways with steps shall comply with T502.4.
Search Results "Bus Loading Zone"
-
T204.4 Doorways with Steps on Over-the-Road Buses
-
T402.11 Gaps
When ramps or bridgeplates are deployed for boarding and alighting, gaps between the ramp or bridgeplate surface and floor of non-rail vehicles shall not permit passage of a sphere...
-
§ 38.39(a)
(a) Where destination or route information is displayed on the exterior of a vehicle, each vehicle shall have illuminated signs on the front and boarding side of the vehicle.
-
§ 38.39 Destination and route signs
[See subsections ...]
-
§ 38.23 Mobility aid accessibility
[See subsections ...]
-
§ 37.3 Public school transportation
Public school transportation means transportation by schoolbus vehicles of schoolchildren, personnel, and equipment to and from a public elementary or secondary school and...
-
New and Altered Permanently Installed Amusement Rides
Such an extensive alteration to an amusement ride may well require that new load and unload areas be designed and constructed....
-
T208.2 Connection to Doorways
A passenger access route shall connect each wheelchair space to doorways that provide a means of accessible boarding and alighting in accordance with T208.2.
-
T404.2 Vehicle Floor and Boarding Platform Coordination
The design of non-rail vehicles shall be coordinated with the boarding platforms to minimize the gap between the vehicle floor and the boarding platforms.
-
Where must the wheelchair symbol be posted?
entrances to a building if the main entrance is not accessible Accessible Parking Spaces and Loading Zones The only legal requirement for accessible parking spaces is to post...
-
Gaps: ADA Standard Section 1002.4.3
Floors of amusement rides with wheelchair spaces and floors of load and unload areas shall be coordinated so that, when amusement rides are at rest in the load and unload position, the vertical...
-
11B-1002.5.2 Transfer height
The height of amusement ride seats designed for transfer shall be 14 inches (356 mm) minimum and 24 inches (610 mm) maximum measured from the surface of the load and unload area....
-
11B-1002.5.2 Transfer height
The height of amusement ride seats designed for transfer shall be 14 inches (356 mm) minimum and 24 inches (610 mm) maximum measured from the surface of the load and unload area....
-
11B-1002.5.2 Transfer height
The height of amusement ride seats designed for transfer shall be 14 inches (356 mm) minimum and 24 inches (610 mm) maximum measured from the surface of the load and unload area....
-
§ 38.159(b)(9) Platform deflection
platform (not including the entrance ramp) shall not deflect more than 3 degrees (exclusive of vehicle roll or pitch) in any direction between its unloaded position and its position when loaded...
-
T201.1 General
Non-rail vehicles purchased, leased or remanufactured by entities covered by the Americans with Disabilities Act (ADA) shall comply with the requirements in the Non-Rail Vehicle...
-
§ 38.155(a)
(a) Handrails and stanchions shall be provided in the entrance to the vehicle in a configuration which allows passengers to grasp such assists from outside the vehicle while starting...
-
Accessible Routes
As previously discussed, an accessible route is also required to connect the load and unload areas of rides that are not required to comply with the guidelines....
-
1002.5.2 Transfer Height
The height of amusement ride seats designed for transfer shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the surface of the load and unload area....
-
11B-1002.5 Amusement ride seats designed for transfer
Amusement ride seats designed for transfer shall comply with Section 11B-1002.5 when positioned for loading and unloading....
-
1002.5 Amusement Ride Seats Designed for Transfer
Amusement ride seats designed for transfer shall comply with 1002.5 when positioned for loading and unloading. Advisory 1002.5 Amusement Ride Seats Designed for Transfer....
-
11B-1002.5 Amusement ride seats designed for transfer
Amusement ride seats designed for transfer shall comply with Section 11B-1002.5 when positioned for loading and unloading....
-
11B-1002.5 Amusement ride seats designed for transfer
Amusement ride seats designed for transfer shall comply with Section 11B-1002.5 when positioned for loading and unloading....
-
1002.5 Amusement Ride Seats Designed for Transfer
Amusement ride seats designed for transfer shall comply with 1002.5 when positioned for loading and unloading. Advisory 1002.5 Amusement Ride Seats Designed for Transfer....