Door openings shall provide a clear width of 32 inches (815 mm) minimum....
Search Results "Automatic Door"
Filters
Commonly Searched Documents
-
404.2.3 Clear Width
-
General: ADA Standard Section 707.1
Automatic teller machines and fare machines shall comply with 707. Advisory 707.1 General....
-
4.13.11* Door Opening Force
The maximum force for pushing or pulling open a door shall be as follows:...
-
404.2.4.1 Swinging Doors and Gates
Swinging doors and gates shall have maneuvering clearances complying with Table 404.2.4.1....
-
POWER-ASSISTED DOOR
POWER-ASSISTED DOOR....
-
404.2.1 Revolving Doors, Gates, and Turnstiles
404.2.1 Revolving Doors, Gates, and Turnstiles. Revolving doors, revolving gates, and turnstiles shall not be part of an accessible route....
-
Power-assisted Door
A door used for human passage with a mechanism that helps to open the door, or relieves the opening resistance of a door, upon the activation of a switch or a continued force applied to...
-
POWER-ASSISTED DOOR
[DSA-AC] A door used for human passage with a mechanism that helps to open the door, or relieves the opening resistance of a door, upon the activation of a switch or a continued force applied...
-
11B-407.3.4 Door and signal timing
The minimum acceptable time from notification that a car is answering a call until the doors of that car start to close shall be calculated from the following equation: T = D/(1.5 ft/...
-
11B-407.3.4 Door and signal timing
The minimum acceptable time from notification that a car is answering a call until the doors of that car start to close shall be calculated from the following equation: T = D/(1.5 ft/...
-
707 Automatic Teller Machines and Fare Machines
Advisory 707 Automatic Teller Machines and Fare Machines. Interactive transaction machines (ITMs), other than ATMs, are not covered by 707....
-
707 Automatic Teller Machines and Fare Machines
Advisory 707 Automatic Teller Machines and Fare Machines. Interactive transaction machines (ITMs), other than ATMs, are not covered by Section 707....
-
Input: ADA Standard Section 707.6
Input devices shall comply with 707.6.
-
Function Keys: ADA Standard Section 707.6.3
Function keys shall comply with 707.6.3.
-
Visibility: ADA Standard Section 707.7.1
The display screen shall be visible from a point located 40 inches (1015 mm) above the center of the clear floor space in front of the machine.
-
11B-707.6.3 Function keys
Function keys shall comply with Section 11B-707.6.3.
-
11B.707.7.1.1 Vertically mounted display screen
Where display screens are mounted vertically or tipped away from the viewer less than 30 degrees, the center line of the display screen and other display devices shall be no more...
-
11B.707.7.1.3 Horizontally mounted display screen
Where display screens are mounted tipped away from the viewer 60 degrees to 90 degrees (horizontal) from vertical, the center line of the display screen and other display devices...
-
11B.707.7.1.2 Angle-mounted display screen
Where display screens are mounted tipped away from the viewer 30 degrees to less than 60 degrees from vertical, the center line of the display screen and other display devices shall...
-
11B-407.3.4 Door and signal timing
The minimum acceptable time from notification that a car is answering a call until the doors of that car start to close shall be calculated from the following equation: T = D/(1.5 ft/...
-
2.2.6 Door Use
2.2.6 Door Use Our study of door use had three main objectives all intended to provide groundwork for future studies aimed at design guidelines and standards that would make doors more...
-
404.2.4.1 Swinging Doors and Gates
Swinging doors and gates shall have maneuvering clearances complying with Table 404.2.4.1....
-
11B-404.2.8.2 Spring hinges
Door and gate spring hinges shall be adjusted so that from the open position of 70 degrees, the door or gate shall move to the closed position in 1.5 seconds minimum....
-
Door and Gate Surfaces [§404.2.10]
Door and Gate Surfaces [§404.2.10] The bottom surface of doors and gates on the push side must be smooth to a height of at least 10”....