Note that examination tables and chairs only use bolsters on certain areas of the transfer surface....
Search Results "Door Surface"
-
SEAT HEIGHT MEASUREMENT DETAIL
-
1.3.2 Focus Following NPRM Comments
This review identified four major issue areas for the MDE Advisory Committee to address, as follows: Transfer surface height and size Permitted obstructions to the transfer surface...
-
I. Public Toilet Rooms
In all public and common use toilet rooms throughout the Hotel and the Tower, Defendants will provide at least one lavatory with a counter-top that is 34 inches above the finish floor surface...
-
Card Catalogs and Magazine Displays [8.4]
Requirements for fixed counters and tables [4.32] specify a surface height (34 inches maximum) and knee clearance below appropriate for extended use as a writing/work surface....
-
Pilot Rock BPR2 Bear Resistant Trash and Recycling Receptacle
Six-point surface anchor base with ½” x 5” concrete screw anchor bolts included. Unit must be anchored to be bear resistant....
-
SafePath VulcanLanding™ Rubber Transition Ramp
Modifying vertical rises at door thresholds often requires more than just a ramp, it requires a level-landing, otherwise known as maneuverable clearance area, a firm and stable level surface...
-
Landscape Forms Inc. Chase Park Trash Receptacle
Add a logo band to portray spirit and branding. 40 gallon top-opening style 36 gallon side-opening style Constructed of cast aluminum sides and door; spun aluminum top; cast iron...
-
Slope
The incline of a surface....
-
Slope
The incline of a surface. ...
-
IMPLICATION OF A 19-INCH MINIMUM STANDARD FOR THE HIGHEST POINT IN THE LOWEST ADJUSTABLE POSITION
However, shorthand references to 19 inches as the minimum standard as used in this minority report should not be equated with a 19-inch transfer surface height, for two major reasons....
-
¼ Inch Minus Limestone
The surface was installed in two rolled and compacted 3 inch lifts....
-
Areas for further work
Areas for further work In the process of assisting the various organizations that represent surface materials and professional groups the following issues were identified as parameters...
-
11B-803.6 Mirrors
Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground....
-
1011.2.4 Openings
Openings in the clear ground space surface shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1011.2.4 Openings. ...
-
1011.2.4 Openings
Openings in the clear ground space surface shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1011.2.4 Openings....
-
11B-803.6 Mirrors
Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground....
-
11B-803.6 Mirrors
Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground....
-
Eunice Noell-Waggoner, IES, LC. Value, Contrast and Reflections
Reflective & Transparent Surfaces can be Dangerous Vertical Surfaces (slide 4) Two examples are shown of hazards from reflective and transparent vertical surfaces....
-
Literature Cited
ASTM F1292 Standard Specification for Impact Attenuation of Surface Systems Under and Around Playground Equipment, ASTM, West Conshohocken,PA 19428 American Society for Testing and Materials...
-
Accessible parking
When parking is near the main door of the facility, these patrons have strength left after entering your business to shop, enjoy entertainment, or eat heartily....
-
e-vi
Are signs mounted on both sides of the elevator hoist way door opening (for each elevator and at each floor) that designate the floor with 2-inch minimum-height raised letters and Braille...
-
Sec.36.207(b)
the residence covered under paragraph (a) of this section extends to those elements used to enter the place of public accommodation, including the homeowner's front sidewalk, if any, the door...
-
4.3.3 WIDTH
The minimum clear width of an accessible route shall be 36 in (915 mm) except at doors (see 4.13.5)....
-
Identification: ADA Standard Section 502.6
Section 502.6 covers the current ADA Standards for parking space identification signs.
