It does not include normal maintenance, repair, reroofing, interior decoration, or changes to mechanical and electrical systems....
Search Results "Hybrid Surface System"
-
ALTERATION
-
218.2 New and Altered Fixed Guideway Stations
New and altered stations in rapid rail, light rail, commuter rail, intercity rail, high speed rail, and other fixed guideway systems shall comply with 810.5 through 810.10....
-
11B-807.3.1 Alarms
Where audible emergency alarm systems are provided to serve the occupants of cells, visible alarms complying with Section 11B-702 shall be provided....
-
§ 38.159(c)(8) Handrails
grasp them from outside the vehicle while starting to board, and to continue to use them throughout the boarding process, and shall have the top between 30 inches (760 mm) above the ramp surface...
-
11B-1002.5 Amusement ride seats designed for transfer
Where possible, designers are encouraged to locate the ride seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
1009 Swimming Pools, Wading Pools, and Spas
Specifications are provided for various means of providing pool access, including pool lifts, sloped entries, transfer walls, transfer systems, and stairs....
-
12142(c)(1)(A)
(A) to remanufacture a vehicle for use on such system so as to extend its usable life for 5 years or more, which remanufacture begins (or for which the solicitation is made) after the 30th...
-
11B-705.1.1.1 Dome size
Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (22.9 mm) minimum and 0.92 inch (23.4 mm) maximum, a top diameter of 0.45 inch (11.4 mm) minimum and...
-
903.4 Back Support
Back support shall be 42 inches (1065 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (455 mm) minimum above the seat...
-
11B-904.4.2 Forward approach
A portion of the counter surface that is 36 inches (914 mm) long minimum and 34 inches (864 mm) high maximum shall be provided....
-
Tork Image Design™ Matic® Hand Towel Roll Dispenser with Intuition® Sensor, Recessed
Image Design™ Matic® Hand Towel Roll Dispenser with Intuition® Sensor Recessed features a gently brushed stainless steel with fine lines; and subtle curves provide clean lines and smooth surfaces...
-
4.32.3 KNEE CLEARANCES
If seating for people in wheelchairs is provided at tables, counters, and work surfaces, knee spaces at least 27 in (685 mm) high, 30 in (760 mm) wide, and 19 in (485 mm) deep shall be provided...
-
12162(a)(4)(B)(ii)
(ii) appropriate auxiliary aids and services, including a hard surface on which to eat, shall be provided to ensure that other equivalent food service is available to individuals with disabilities...
-
303 Changes in Level
Section 303 addresses vertical changes in level in floor or ground surfaces. No changes have been made to this section....
-
Summary of Significant Changes
to provide automated stop and route announcement systems on all large vehicles operating in fixed route bus service that stop at multiple designated stops....
-
Operable Parts of Windows
Information was sought on any other design impacts, such as the use of the space or cavity below windows for mechanical or other building systems....
-
12162(e)(2)(A)(ii)(I) Intercity rail
(I) Intercity rail All stations in the intercity rail transportation system shall be made readily accessible to and usable by individuals with disabilities, including individuals who...
-
2. Benefits: Qualitative Summary of Benefits
Individuals with other types of disabilities may also experience benefits from the automated announcement system requirement....
-
2.8 Openings
Openings in the surface of ORARs shall be small enough to prevent passage of a 1/2 inch (13 mm) diameter sphere....
-
M12
If a mirror is provided, is the bottom of the reflecting surface no higher than 40 inches above the floor or is a full length mirror provided?...
-
SECTION#2
SECTION#2 For the following questions, please answer every item pertaining to the trail surface composition....
-
1008.3.1.1 Size
Transfer platforms shall have level surfaces 14 inches (355 mm) deep minimum and 24 inches (610 mm) wide minimum....
-
1008.3.2.1 Size
Transfer steps shall have level surfaces 14 inches (355 mm) deep minimum and 24 inches (610 mm) wide minimum....
-
1009.3.1 Sloped Entries
EXCEPTION: Where sloped entries are provided, the surfaces shall not be required to be slip resistant....