Recommendation: It is good practice to avoid specifying precisely to the maximum or minimum where possible so that achieved dimensions fall within ADAAG requirements....
Search Results "Maximum Dimension"
Filters
Commonly Searched Documents
-
Dimensional Tolerances [3.2]
-
11B-407.4.6.2.1 Size and shape
Buttons shall have square shoulders, be ¾ inch (19.1 mm) minimum in their smallest dimension and be raised 1/8 inch (3.2 mm) plus or minus 1/32 inch (0.8 mm) above the surrounding surface...
-
M301.3 Transfer Supports
Circular cross sections – Circular cross sections must have an outside diameter of 1¼ inches minimum and 2 inches maximum....
-
Standing Supports (M304.3 and M305.3)
The bottom of the support would be required to be 34 inches minimum and 37 inches maximum above the standing surface....
-
T302.3 Openings
Elongated openings shall be placed so that the long dimension is perpendicular to the dominant direction of travel. EXCEPTIONS: 1....
-
Clearance Around Base (M301.4.2 and M302.4.2)
The width of the base permitted within this clearance would be 26 inches wide maximum at the edge of the examination surface and is permitted to increase at a rate of 1 inch in width for...
-
14.3 Q...are there any requirements for the inside dimensions of these individual parking garages?
A. Yes. These garages would be public and common use space, even though the individual garages may be assigned to a particular dwelling unit. Therefore, at least two percent of the...
-
4.1.6(4)(a)
Table 2 -- Allowable Ramp Dimensions for Construction in Existing Sites, Buildings, and Facilities Slope* Maximum Rise Maximum Run Steeper than 1...
-
1. Thigh Breadth
Thigh breadth for this analysis was computed as the larger of two dimensions, the horizontal distance between the lateral (outer) aspect of the hips, and the horizontal distance between...
-
Figure 408.4.1(c) Limited-Use/Limited-Application (LULA) Elevator Car Dimensions – Drawing from the U.S. Access Board
-
Figure 408.4.1(b) Limited-Use/Limited-Application (LULA) Elevator Car Dimensions – Drawing from the U.S. Access Board
-
Is there a maximum travel distance to entrances from parking and other site arrival points?
No, the Standards do not limit the travel distance to accessible entrances. Accessible parking spaces must be located on the shortest accessible route to an accessible entrance...
-
604.2 Location
The centerline of the water closet shall be 16 inches (405 mm) minimum to 18 inches (455 mm) maximum from the side wall or partition, except that the water closet shall be 17 inches (430...
-
Bus Stop Pads
The proposed rule specified that these dimensions were required to "the maximum extent allowed by legal or site constraints" (1002.2.2)....
-
Clearance in Base (M301.4.1 and M302.4.1)
Equipment components are permitted to be located within 8 inches maximum of the centerline of the clearance width. Question 25....
-
A. Measuring Slope and Cross Slope
Now, take the tape measure and measure the open gap at the downhill end of the level, as shown in the photo opposite - this the "critical dimension"....
-
11B-409.4.6.1 Size
Control buttons shall be ¾ inch (19.1 mm) minimum in their smallest dimension....
-
11B-407.2.1.2 Size and shape
Call buttons shall have square shoulders, be ¾ inch (19.1 mm) minimum in the smallest dimension and shall be raised 1/8 inch (3.2 mm) plus or minus 1/32 inch (0.8 mm) above the surrounding...
-
Size: ADA Standard Section 407.4.6.2.1
Section 407.4.6.2.1 covers the current ADA Standards for the size of the elevator car control buttons.
-
Controls
Controls Push buttons or plates and switches are subject to relevant requirements for controls and operating mechanisms, including the maximum 5 Ib operating force....
-
Size: ADA Standard Section 409.4.6.1
Section 409.4.6.1 covers the current ADA Standards for the size of the car controls in private residence elevators.
-
Call Buttons: ADA Standard Section 409.2
Section 409.2 covers the current ADA Standards for call buttons in private residence elevators.
-
611 Washing Machines and Clothes Dryers
The proposed rule required the door of top loading machines and the door opening of front loading machines to be 34 inches maximum above the floor (611.4)....
-
11B-812.10.4 Location
circulation path is not provided adjacent to the head end of the vehicle space or access aisle, the EV charger may be located within the projected width of the access aisle 36 inches (914 mm) maximum...
