Key HETAP and UTAP Differences HETAP follows the same general principles as its predecessor, UTAP (the Universal Trail Assessment Process). Both collect objective trail...
Search Results "Cross Slope"
2010 ADA Definition
Cross Slope: The slope that is perpendicular to the direction of travel (see running slope).
Filters
Commonly Searched Documents
-
Beneficial Designs High Efficiency Trail Assessment Process (HETAP) Software 3.0 Wheeled Instrumentation Sensor Package for Data Collection
-
11B-802.1.1 Floor or ground surface
Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted. Exception: Reserved....
-
1. Location
Generally, you must provide curb ramps wherever a sidewalk or other pedestrian walkway crosses a curb. ...
-
405 Ramps
Technical provisions address running slope, cross slope, handrails, landings, edge protection, and other elements....
-
Cross Section of Gripping Surfaces
specify the following dimensions for grab bars to enable individuals with disabilities to firmly grasp the grab bars and support themselves during transfers: • Grab bars with circular cross...
-
11B-502.4 Floor or ground surfaces
Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted. Exception: Reserved. Advisory 11B-502.4 Floor or ground surfaces....
-
Interior Routes
with trim on exposed edge. 11B-302.2 Vertical clearances/protrusions along circulation paths. 11B-307 Running and cross...
-
Interior Routes
with trim on exposed edge. 11B-302.2 Vertical clearances/protrusions along circulation paths. 11B-307 Running and cross...
-
Are curved or circular ramps allowed?
Ramps without level landings at changes in direction typically will not meet the Standards due to resulting compound slopes....
-
11B-406.5.1 Location
Curb ramps at marked crossings shall be wholly contained within the markings, excluding any flared sides. Exception: Diagonal curb ramps shall comply with Section 11B-406.5.9....
-
Calibrating the level used for measuring accessible routes for ADAAG Compliance by ACT Services Consulting
Requires the Premium User plan or above. (Login or upgrade your account!) -
M305.2.4.1 Circular Cross Section
Transfer supports with circular cross sections shall have an outside diameter of 1 ¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
Sears Brands, LLC Craftsman Digital Torpedo Level
Description Item # 00948295000P Model # 48295 Craftsman Digital Torpedo Level Keeps It Plumb, Even in Tight Spaces The Digital Torpedo takes the guesswork out of reading...
-
Trail Grade
When expressed as a ratio of rise to length to the term used is running slope....
-
A6
If a curb ramp is provided, is the running slope of the ramp surface (not counting the side flares) no more than 1:12 or 8.33% [ADA Standards § 4.7.2] Yes No...
-
1016.7.1 Maximum Running Slope and Segment Length
Table 1016.7.1 Maximum Running Slope and Segment Length Running Slope of Outdoor Recreation Access Route Segment Maximum Length of Segment...
-
1016.7.1 Maximum Running Slope and Segment Length
Table 1016.7.1 Maximum Running Slope and Segment Length Running Slope of Outdoor Recreation Access Route Segment Maximum Length of Segment Steeper than But...
-
Wheelchair Spaces
Wheelchair spaces must be level (2% maximum slope in any direction) and adjoining routes and maneuvering spaces must provide flush connections so that maneuvering to and from spaces does...
-
B7-b
Is the slope (up or down the ramp) no more than 1:12? [ADA Standards § 4.7.2] Yes No Note: 1:12 is one inch of vertical height for each 12 inches of length....
-
e-ii
Is the running slope (up or down the ramp) no more than 1:12?...
-
5.1.2 Level or Sloped Entry
Camp shelters providing roll-in access shall have a level or sloped entry that complies with the FSORAG Outdoor Recreation Access Route technical provisions if the camp shelter is in a campground...
-
M305.2.4.2 Non-Circular Cross Section
Transfer supports with non-circular cross sections shall have a cross-section dimension of 2 inches (51 mm) maximum and a perimeter dimension of 4 inches (100 mm) minimum and 4.8 inches...
