Space under an element between the finish floor or ground and 9 inches (229 mm) above the finish floor or ground shall be considered toe clearance and shall comply with Section 11B-306.2...
Search Results "Extended Floor Surface"
-
11B-306.2.1 General
-
11B-306.2.1 General
Space under an element between the finish floor or ground and 9 inches (229 mm) above the finish floor or ground shall be considered toe clearance and shall comply with Section 11B-306.2...
-
306.2.1 General
Space under an element between the finish floor or ground and 9 inches (230 mm) above the finish floor or ground shall be considered toe clearance and shall comply with 306.2....
-
5.4.1.2 Transfer and Positioning Support Location for Imaging Equipment
Transfer supports should be provided for imaging equipment with transfer surfaces with depths of less than or equal to 24 inches....
-
Definition of "Mezzanine"
"Mezzanine" is now defined by the same definition used in the IBC: "An intermediate level or levels between the floor and ceiling of any story with an aggregate floor area of not more than...
-
M9
Does the lavatory have at least a 29-inch-high clearance under the front edge and the top of the rim no more than 34 inches above the floor?...
-
Slope
The incline of a surface....
-
Slope
The incline of a surface. ...
-
M303.2.4.2.2 Height
Wheelchair spaces shall include toe clearance 9 inches (230 mm) high minimum above the floor measured to a depth of 6 inches (150 mm) maximum measured from the toe end of the wheelchair...
-
Elevators
Elevators Common Problem: Lodging facilities with more than two floors of occupiable space - including any basement levels - do not have full-size passenger elevators available for...
-
2. Equipment Clearances for Breast Platforms
Additionally, this commenter raised concerns that mammography equipment must have a stabilizing flange or foot at its base to prevent the equipment from tipping when the gantry is extended...
-
22. How can I get copies of the ASTM standards that apply to play areas?
American Society for Testing and Materials, 100 Bar Harbor Drive, West Conshohocken, Pennsylvania 19428, www.astm.org: ASTM F 1292-99 Standard Specification for Impact Attenuation of Surface...
-
SEAT HEIGHT MEASUREMENT DETAIL
Note that examination tables and chairs only use bolsters on certain areas of the transfer surface....
-
1.3.2 Focus Following NPRM Comments
This review identified four major issue areas for the MDE Advisory Committee to address, as follows: Transfer surface height and size Permitted obstructions to the transfer surface...
-
11B-206.2.3 Multi-story buildings and facilities
For example, a 3-story office building with 4500 sf on the first floor, 2500 sf on the second floor and 1500 sf on the third floor would not qualify for the exception because one of the...
-
11B-206.2.3 Multi-story buildings and facilities
For example, a 3-story office building with 4500 sf on the first floor, 2500 sf on the second floor and 1500 sf on the third floor would not qualify for the exception because one of the...
-
11B-206.2.3 Multi-story buildings and facilities
For example, a 3-story office building with 4500 sf on the first floor, 2500 sf on the second floor and 1500 sf on the third floor would not qualify for the exception because one of the...
-
1011.2.4 Openings
Openings in the clear ground space surface shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1011.2.4 Openings. ...
-
1011.2.4 Openings
Openings in the clear ground space surface shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1011.2.4 Openings....
-
IMPLICATION OF A 19-INCH MINIMUM STANDARD FOR THE HIGHEST POINT IN THE LOWEST ADJUSTABLE POSITION
However, shorthand references to 19 inches as the minimum standard as used in this minority report should not be equated with a 19-inch transfer surface height, for two major reasons....
-
Areas for further work
Areas for further work In the process of assisting the various organizations that represent surface materials and professional groups the following issues were identified as parameters...
-
11B-233.3.6 Graduate student and faculty housing at a place of education
including, but not limited to, the provisions in sections 233 and 809. 1) In sleeping rooms with more than 25 beds covered by this part, a minimum of 5% of the beds shall have clear floor...
-
11B-233.3.6 Graduate student and faculty housing at a place of education
including, but not limited to, the provisions in sections 233 and 809. 1) In sleeping rooms with more than 25 beds covered by this part, a minimum of 5% of the beds shall have clear floor...
-
2. Analysis of footrest clearance height and depth
Analysis of footrest clearance height and depth Any base support or flange for the mammography machine at floor level (inside the clear floor space width) would obstruct some wheelchair...