signs identifying permanent rooms and spaces, directional and informational signs (except those relating to accessible means of egress), and entrance signs are not required to comply with tactile...
Search Results "Tactile Glove Technology"
Filters
Commonly Searched Documents
-
11B-216.1 General
-
1007.6.5 Identification
Additionally, tactile signage complying with ICC A117.1 shall be located at each door to an area of refuge....
-
1003.2.13.5.5 Identification
Additionally, tactile signage complying with ICC A117.1 shall be located at each door to an area of refuge....
-
Mounting Height and Location
Section 703.4 covers the mounting height and location of signs with tactile characters....
-
Designations: ADA Standard Section 216.2
Section 216.2 covers scoping requirements in the current ADA Standards for sign designations.
-
3. Relationship between Functional Performance Criteria and Technical Provisions
criteria in the sense that agencies should look first to applicable technical provisions, and only turn to the functional performance criteria when such requirements did not fully address the technology...
-
SUMMARY OF PRELIMINARY REGULATORY ANALYSIS
The Board’s existing standards and guidelines are greatly in need of a “refresh” to keep up with technological changes over the past fifteen years....
-
Intelligent Assistive Technology and Systems Lab
Welcome to the Intelligent Assistive Technology and Systems Lab (IATSL), located in the Department of Occupational Science and Occupational Therapy at the University of Toronto....
-
§382.57(c)(6) Input
(6) Input. Input devices must comply with paragraphs (c)(6)(i) through (iv) of this section.
-
§ 382.57(c)(6) Input
(6) Input. Input devices must comply with paragraphs (c)(6)(i) through (iv) of this section.
-
Stroke Thickness: ADA Standard Section 703.5.7
Stroke thickness of the uppercase letter “I” shall be 10 percent minimum and 30 percent maximum of the height of the character.
-
11B-703.5.7 Stroke thickness
Stroke thickness of the uppercase letter “I” shall be 10 percent minimum and 20 percent maximum of the height of the character. [2010 ADA Standards] 703.5.7 Stroke Thickness....
-
Robots invade the GlobalNOC at IU
The GlobalNOC at IU uses telepresence robots to ensure that staff members working remotely can still be an integral part of the team.
-
Center on Knowledge Translation for Technology Transfer (KT4TT)
The Center on Knowledge Translation for Technology Transfer (KT4TT) is a program of the Center of Assistive Technology at the University at Buffalo, sponsored by the National Institute on...
-
407.2.3.1 Floor Designation
Floor designations shall be provided in both tactile characters and braille. Tactile characters shall be 2 inches (51 mm) high minimum....
-
407.2.3.1 Floor Designation
Floor designations shall be provided in both tactile characters and braille. Tactile characters shall be 2 inches (51 mm) high minimum....
-
Figure 407.2.3.1 Floor Designations on Jambs of Elevator Hoistway Entrances – Drawing from the U.S. Access Board
-
407.2.3.1 Floor Designation
Floor designations shall be provided in both tactile characters and braille. Tactile characters shall be 2 inches (51 mm) high minimum....
-
§27.71(k)(6)(ii) Alphabetic keys.
The “F” and “J” keys must be tactilely distinct from the other keys....
-
§ 27.71(k)(6)(ii) Alphabetic keys
The “F” and “J” keys must be tactilely distinct from the other keys....
-
Assistive Technology Industry Association
The Assistive Technology Industry Association (ATIA) is a not-for-profit membership organization of manufacturers, sellers and providers of technology-based assistive devices and/or services...
-
E207 Software
[See subsections ...]
-
C205 Software
[See subsections ...]
