In alternate roll-in type shower compartments, grab bars shall be provided on the back wall and the side wall farthest from the compartment entry....
Search Results "Grab Bar"
Filters
Commonly Searched Documents
-
11B-608.3.3 Alternate roll-in type shower compartments
-
11B-608.3.3 Alternate roll-in type shower compartments
In alternate roll-in type shower compartments, grab bars shall be provided on the back wall and the side wall farthest from the compartment entry....
-
Figure 609.2.2 Grab Bar Non-Circular Cross Section – Drawing from the U.S. Access Board
-
11B-212.2 Kitchens, kitchenettes, and wet bars
Kitchens, kitchenettes and wet bars shall comply with Section 11B-804. [2010 ADA Standards] 212.2 Kitchens and Kitchenettes. Kitchens and kitchenettes shall comply with 804....
-
Figure 607.4.1 Grab Bars for Bathtubs with Permanent Seats – Drawing from the U.S. Access Board
-
Figure 608.3.1 Grab Bar for Transfer Type Showers – Drawing from the U.S. Access Board
-
Figure 607.4.2 Grab Bars for Bathtubs with Removable In-Tub Seats – Drawing from the U.S. Access Board
-
7(2)(b)(iv)
(iv) Toilets are located within bathrooms in a manner that permit a grab bar to be installed on one side of the fixture....
-
11B-608.3.1 Reserved
11B-608.3.1 Reserved.
-
1. Accessible toilet
Accessible toilet with rear and side grab bars, clear floor space for wheelchair transfer, and an accessible flush valve....
-
7(2)(b)
(b) Bathrooms that have reinforced walls for grab bars (see Requirement 6) would meet section 100.205(c)(3)(iv) if: Note: Clear floor space beside tub may overlap with clear floor space...
-
Meeting User Needs
As a result, grab bars on both sides of a toilet that would support a standing transfer were provided rather than alongside and behind the toilet as would be used for a sliding transfer....
-
11B-212 Kitchens, kitchenettes, wet bars and sinks
212 Kitchens, Kitchenettes, and Sinks ETA Editor’s Note The CBC includes wet bars. Therefore, the CBC is more inclusive....
-
A4.16.5 Flush Controls
If administrative authorities require flush controls for flush valves to be located in a position that conflicts with the location of the rear grab bar, then that bar may be split or shifted...
-
A4.16.5 FLUSH CONTROLS
If administrative authorities require flush controls for flush valves to be located in a position that conflicts with the location of the rear grab bar, then that bar may be split or shifted...
-
604.9.6 Dispensers
There shall be a clearance of 1½ inches (38 mm) minimum below the grab bar. Dispensers shall not be of a type that controls delivery or that does not allow continuous paper flow....
-
604.9.6 Dispensers
There shall be a clearance of 1 1/2 inches (38 mm) minimum below the grab bar. Dispensers shall not be of a type that controls delivery or that does not allow continuous paper flow....
-
604.9.6 Dispensers
There shall be a clearance of 1½ inches (38 mm) minimum below the grab bar. Dispensers shall not be of a type that controls delivery or that does not allow continuous paper flow....
-
11B-604.9.6 Dispensers
There shall be a clearance of 1½ inches (38 mm) minimum below the grab bar. Dispensers shall not be of a type that controls delivery or that does not allow continuous paper flow....
-
11B-604.9.6 Dispensers
There shall be a clearance of 1½ inches (38 mm) minimum below the grab bar. Dispensers shall not be of a type that controls delivery or that does not allow continuous paper flow....
-
11B-604.9.6 Dispensers
There shall be a clearance of 11/2 inches (38 mm) minimum below the grab bar. Dispensers shall not be of a type that controls delivery or that does not allow continuous paper flow....
-
11B-604.7 Dispensers and disposal units
The outlet of the dispenser shall be below the grab bar, 19 inches (483 mm) minimum above the finish floor and shall not be located behind grab bars....
