by establishing an advisory committee composed of members of the design and construction industry, the building code community, state and local government entities, and individuals with disabilities...
Search Results "CDIHP: Center for Disability Issues and the Health Professions"
-
The Revised Guidelines (2004 ADAAG)
-
11B-407.2.2.2 Visible signals
Visible signal fixtures shall be centered at 72 inches (1829 mm) minimum above the finish floor or ground....
-
Paragraph (g) Operable without time-dependent controls (Section-by-Section Analysis)
Some of the discussion on this subject provided by the Trace Center has been included in the appendix....
-
New Construction
This includes play areas located in a variety of settings: parks, schools, childcare facilities, shopping centers, and public gathering areas. ...
-
Islands [4.7.11]
If there is no level space between ramps, wheelchairs can "bottom out" or "high center" while proceeding down one ramp while the back wheels are coming up the other slope....
-
Outpatient Facilities
Examples include a hospital's clinic or ambulatory care center....
-
Trail Construction and Maintenance Notebook
The Missoula Technology and Development Center's "Trail Construction and Maintenance Notebook" contains basic trail building information....
-
Clear Floor Space [4.19.3]
Clear Floor Space [4.19.3] Clear floor space should be centered at the fixture (although this is not specifically required by ADAAG)....
-
Activation button
Activation button The audio buttons are located in the center of the panels and under the text. Participants expressed concern over the difficulty of finding it....
-
End of Document
CAVALIERS OPERATING COMPANY, LLC /s/ Len Komoroski Len Komoroski President Cavaliers Operating Company, LLC 1 Center Court Cleveland, OH 44115 Date: December 13, 2012...
-
Controls [§404.3.5]
The clear floor space is not required to be centered at controls, but should be located to facilitate reach and operation....
-
1133A.7 Knee and toe space
The knee and toe space shall be 30 inches (762 mm) wide minimum, centered on the sink, countertop or appliance. ...
-
11B-407.4.7.2 Keypads
Keypads shall be identified by characters complying with Section 11B-703.5 and shall be centered on the corresponding keypad button. The number five key shall have a single raised dot....
-
Courtroom Access
Specifically because Assembly Areas include courtrooms in the definition and because these spaces have less than 300 and they are both presently organized in rows without a center aisle...
-
§1630.1(c)(1) In general
in this part, this part does not apply a lesser standard than the standards applied under title V of the Rehabilitation Act of 1973 (29 U.S.C. 790-794a, as amended), or the regulations issued...
-
[A] PERMIT
An official document or certificate issued by the authority having jurisdiction which authorizes performance of a specified activity. Advisory Definition of PERMIT....
-
11B-703.3.1 Dimensions and capitalization
Measured center to center....
-
407.4.1 Car Dimensions
Clear Width Inside Car, Side to Side Inside Car, Back Wall to Front Return Inside Car, Back Wall to Inside Face of Door Centered...
-
Initial Measures and Transfer Setup
The device seat to floor height was measured as the linear distance between the front of the seat, center-line point on top of the cushion (if present) and the floor (Figure 3 left). ...
-
11B-703.3.1 Dimensions and capitalization
Measured center to center....
-
11B-703.3.1 Dimensions and capitalization
Measured center to center. ...
-
Roberta Null, Ph.D., ASID. Training for Blind and Low Vision Persons: Color Contrast
Center for the Blind I did a lot of work years ago teaching kitchen design, and found out about the Center for the Blind in San Diego (slide 1), which was right off of our campus at...
-
DOT Response to Comments
Reasonable modification is a central concept of disability nondiscrimination law, based on the principle that it is essential for entities to consider individuals with disabilities as individuals...
-
Section 1193.33 Information, documentation and training [1193.25 in the NPRM] (Section-by-Section Analysis)
Manufacturers are also required to ensure usable customer support and technical support in the call centers and service centers, which support their products. Comment....