[DSA-AC] A sloping pedestrian walking surface located at the end(s) of a gangway....
Search Results "Hybrid Surface System"
-
TRANSITION PLATE
-
TRANSITION PLATE
[DSA-AC] A sloping pedestrian walking surface located at the end(s) of a gangway....
-
GRADE BREAK
[DSA-AC] The line where two surface planes with different slopes meet....
-
CURB CUT
An interruption of a curb at a pedestrian way, which separates surfaces that are substantially at the same elevation....
-
106.5.76 Walk
An exterior prepared surface for pedestrian use, including pedestrian areas such as plazas and courts....
-
Ramp
A walking surface that has a running slope steeper than 1:20....
-
Transition Plate
A sloping pedestrian walking surface located at the end(s) of a gangway....
-
705.1 General
Detectable warnings shall consist of a surface of truncated domes and shall comply with 705....
-
Section 37.105 Equivalent Service Standard
Another provision (schedules/headways) applies only to fixed route systems. This is because these points of comparison apply only to one or the other type system....
-
6.3. Auditoriums Exhibiting Analog Movies
The unit costs for the components of the Rear Window®35 system are presented in Table 6-6....
-
Re: Ernest Castro
I have invented a patent pending system for severely handicapped people who can’t transfer to enter a swimming pool. My wife is paralyzed on the left side from a surgery gone wrong....
-
907.2.6.2.3 Smoke detectors
An approved automatic smoke detection system shall be installed throughout resident housing areas, including sleeping areas and contiguous day rooms, group activity spaces and other common...
-
Automatic Teller Machines and Fare Machines: ADA Standard Section 707
This law covers a variety of products, including computer hardware and software, websites, phone systems, fax machines, copiers, and similar technologies....
-
M305.2.2 Length (Section-by-Section Analysis)
extend horizontally along the transfer surface to within three inches, to allow for manufacturing tolerances....
-
M302.4.1 Clearance in Base
provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
M301.4.1 Clearance in Base
provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
102 Dimensions for Adults and Children
are also provided based on children’s dimensions and anthropometrics for drinking fountains, water closets and other elements located in toilet compartments, lavatories and sinks, dining surfaces...
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
Ramps [4.8]
The curvature and slope typically result in an uneven surface that makes wheelchair maneuvering difficult because not all wheels rest on the surface....
-
Openings in Beach Access Routes
Openings are gaps in the surface of a beach access route. Gaps include spaces between the planks on a boardwalk and drainage holes in temporary or permanent surfaces....
-
Questionnaire
A full version of the questionnaire given to the subjects after traveling over each surface can be found in Appendix C. The questionnaire was developed by the study investigators....
-
M302.4.1 Clearance in Base
provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
M301.4.1 Clearance in Base
provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
11B-801.1 Scope
For example, Section 11B-806 addresses guest rooms in transient lodging facilities while Section 11B-902 contains the technical specifications for dining surfaces....