The side edge of the seat shall be 1 1/2 inches (38 mm) maximum from the adjacent wall....
Search Results "Side Transfer Surface"
Filters
Commonly Searched Documents
-
610.3.1 Rectangular Seats
-
Approach
One side of the wheelchair space must adjoin an accessible route. The turning space may overlap the accessible route and the required clear floor space....
-
11B-602.3 Operable parts
The flow of water shall be activated by a manually operated system that is front mounted or side mounted and located within 6 inches (152 mm) of the front edge of the fountain or an automatic...
-
1015.2 Clear Ground Space
clear ground space 36 inches minimum by 48 inches minimum positioned for either a forward or parallel approach to be provided at each distinct viewing location, and one full unobstructed side...
-
§ 38.107(a)(5)
Doorways on the side wall shall have a minimum clear opening width of 39 inches....
-
§ 38.123(a)(5)
Doorways on the side wall shall have a minimum clear opening width of 39 inches....
-
11B-610.3.1 Rectangular seats
The side edge of the seat shall be 1½ inches (38 mm) maximum from the adjacent wall....
-
Clear Width: ADA Standard Section 404.2.3
Section 404.2.3 covers the current ADA Standards for clear width at manual doors, doorways and manual gates that are part of an accessible route.
-
11B-404.2.3 Clear width
Exceptions: In alterations, a projection of 5/8 inch (15.9 mm) maximum into the required clear width shall be permitted for the latch side stop....
-
Tread Width
The visible trail surface measured perpendicular to the direction of travel....
-
11B-1005.2.1 Height
At least 25 percent of the railings, guards, or handrails shall be 34 inches (864 mm) maximum above the ground or deck surface....
-
Key Differences Between Routes
when necessary for drainage —1:20 (5%) 1:20 (5%) 1:12 (8.33%) 200 feet Concrete, asphalt, boards—1:48 (2%) All other surfaces when necessary for...
-
3. Terminology
Discussion—Elevation measurements may be taken statically, as with rod and level per Test Method E1364 or dynamically using a rolling inclinometer per Test Method E2133. 3.1.1.2 traveled surface...
-
Selection of Methodology
) information (product type, manufacturer name, warranty/guarantees’ information, and similar data) SECTION #3 Trail pre‐installation specifications (soil type/composition, slope of surface...
-
Rebuilding Together El Paso - El Paso, TX
Together we transfer the lives of low income and/or disabled homeowners by improving the safety and health in their home and by revitalizing their communities, as to extend the opportunity...
-
Energy Consumption During Ambulation
Subjects walked on each surface at their preferred pace, until the physiological variables (energy consumption, heart rate, velocity) had stabilized (2‒3 minutes) and the data collection...
-
11B-801.1 Scope
For example, 806 addresses guest rooms in transient lodging facilities while 902 contains the technical specifications for dining surfaces....
-
703.4.1 Height above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
M302.4.2 Clearance Around Base
the diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
M301.4.2 Clearance Around Base
base of diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
1002.4.4.3 Permitted Protrusions in Wheelchair Spaces
protrude a distance of 6 inches (150 mm) maximum along the front of the wheelchair space, where located 9 inches (230 mm) minimum and 27 inches (685 mm) maximum above the floor or ground surface...
-
14.2 Q. If both open and covered parking spaces are provided, how many of each type must be accessible?
., surface parking or garage, that are provided for other residents of the project....
-
801.1 Scope
For example, 806 addresses guest rooms in transient lodging facilities while 902 contains the technical specifications for dining surfaces....
-
4.8.1 General
One fixed showerhead shall be 48 inches (1220 mm) above the floor or ground surface, and one fixed shower head shall be 72 inches (1830 mm) minimum above the floor or ground surface....
