Copies of the referenced standards may be obtained from the Builders Hardware Manufacturers Association, 355 Lexington Avenue, 17th floor, New York, NY 10017 (http://www.buildershardware.com...
Search Results "Court Floor Holding Cell"
Filters
Commonly Searched Documents
-
F105.2.1 ANSI/BHMA
-
Typical Transfer Techniques: Staff Assistance and Patient Lifts
Transfer Techniques: Staff Assistance and Patient Lifts Some individuals will need additional assistance to get on and off an exam table, even if it lowers to 17‒19 inches from the floor...
-
Contrast
However, requirements for ground and floor surfaces in section 302, which require slip resistance, apply to those surfaces with detectable warnings as well....
-
224.6 Housing at a Place of Education
Kitchens within housing units containing accessible sleeping rooms with mobility features (including suites and clustered sleeping rooms) or on floors containing accessible sleeping rooms...
-
307 Protruding Objects
., higher than 27 inches from the floor) and below the standard head room clearance (80 inches), are limited to a 4 inch depth....
-
105.2.1 ANSI/BHMA
Copies of the referenced standards may be obtained from the Builders Hardware Manufacturers Association, 355 Lexington Avenue, 17th floor, New York, NY 10017 (http://www.buildershardware.com...
-
Front grab bar protocol
The preferred grab bar height was measured between the floor and the top of the grab bar surface. ...
-
City of XXX – ADA Transition Plan
to accessible entrance Install sign 2/4 Facilities manager $40 Maintenance and repairs First floor...
-
Requirement 5. Light switches, electrical outlets, thermostats and other environmental controls in accessible locations.
thermostats and other environmental controls would meet section 100.205(c)(3)(ii) if operable parts of the controls are located no higher than 48 inches, and no lower than 15 inches, above the floor...
-
105.2.1 ANSI/BHMA
Copies of the referenced standards may be obtained from the Builders Hardware Manufacturers Association, 355 Lexington Avenue, 17th floor, New York, NY 10017 (http://www.buildershardware.com...
-
205.1 General
Floor electrical receptacles shall not be required to comply with 309. 5. HVAC diffusers shall not be required to comply with 309. 6....
-
i. Medical examination and treatment tables and chairs
course of its enforcement efforts that medical and dental examination tables and chairs often are too high to be accessible, lack stabilization elements, and do not have adequate clear floor...
-
Sight Lines
A variety of factors determine the quality of "vertical" sight lines, such as the distance from performance areas, row spacing, staggering of seats, and floor slope....
-
Washing Machines; Clothes Dryers— Sections 214.2 and 214.3 of the 2010 Standards
would not require a laundry room on an upper story of a non-elevator building to be accessible provided that there is an accessible laundry room serving that same building on the ground floor...
-
III-4.1400 Surcharges
ILLUSTRATION: The ABC pharmacy is located on the second floor of an older four-story building that does not have an elevator....
-
1.1.1 Measurement tools
Digital inclinometers (SmartTool®), floor profilers, and other electronic instruments are capable of measuring to this accuracy. 0.01 ft accuracy for elevations is common in surveying and...
-
1009.9 Signage
Each door providing access to an area of refuge from an adjacent floor area shall be identified by a sign stating: AREA OF REFUGE. 2....
-
[2010 ADAS] 105.2.1 ANSI/BHMA
Copies of the referenced standards may be obtained from the Builders Hardware Manufacturers Association, 355 Lexington Avenue, 17th floor, New York, NY 10017 (http://www.buildershardware.com...
-
§ 38.175(a)
shall be coordinated with the boarding platform design such that the horizontal gap between a car door at rest and the platform shall be no greater than 3 inches and the height of the car floor...
-
Subpart F—Certification of State Labs or Local Building Codes (Preamble, Section-by-Section Analysis)
First, the State or local jurisdiction is required to hold a public hearing on its proposed request for certification and to submit to the Department, as part of the information and materials...
-
Subpart F—Certification of State Labs or Local Building Codes (Section-By-Section Analysis and Response to Comments)
First, the State or local jurisdiction is required to hold a public hearing on its proposed request for certification and to submit to the Department, as part of the information and materials...
-
Trail Study Sites
Layout of the path across the beach was sloped so that the edge of the path would not hold water....
-
Verification of Service Animals
., accept the animal for carriage in the cargo hold). Example 1: A passenger arrives at the gate accompanied by a pot-bellied pig....
-
Development of the 2004 ADA/ABA Guidelines
The Access Board provided further opportunity for participation by holding public hearings....