Revisions made to this section concern: coverage of handrails provided along walking surfaces (505.1) exceptions for aisle stairs and short ramps (505.2) handrails...
Search Results "General Exception"
-
505 Handrails
-
604.9.5 Flush Controls
Flush controls shall be located on the open side of the water closet except in ambulatory accessible compartments complying with 604.8.2....
-
M301.2.3.1 End Transfer Surface
EXCEPTION: Transfer surfaces for imaging equipment with bores shall be permitted to be 21 inches (535 mm) wide minimum but shall not be permitted to be less than the full width of the examination...
-
M301.2.3.2 Side Transfer Surface
EXCEPTION: Transfer surfaces for imaging equipment with bores shall be permitted to be 21 inches (535 mm) wide minimum but shall not be permitted to be less than the full width of the examination...
-
1007.6.2 Separation
Exception: Areas of refuge located within an enclosure for exit access stairways or interior exit stairways....
-
404.2.4 Maneuvering Clearances
[ECTCR UFAS 4.13.6, Fig. 25] EXCEPTION: Entry doors to hospital patient rooms shall not be required to provide the clearance beyond the latch side of the door....
-
504.4 Tread Surface
EXCEPTION: Treads shall be permitted to have a slope not steeper than 1:48. Advisory 504.4 Tread Surface....
-
309.4 Operation
EXCEPTION: Gas pump nozzles shall not be required to provide operable parts that have an activating force of 5 pounds (22.2 N) maximum....
-
504.4 Tread Surface
EXCEPTION: Treads shall be permitted to have a slope not steeper than 1:48. Advisory 504.4 Tread Surface....
-
804.3.2 Height
EXCEPTION: A counter that is adjustable to provide a kitchen work surface at variable heights, 29 inches (735 mm) minimum and 36 inches (915 mm) maximum, shall be permitted....
-
309.4 Operation
EXCEPTION: Gas pump nozzles shall not be required to provide operable parts that have an activating force of 5 pounds (22.2 N) maximum....
-
401.1 Scope
EXCEPTION: Hardware that is assistive technology shall not be required to conform to the requirements of this chapter....
-
B. Recruitment
may not limit their recruitment for employees to schools, communities, or companies disproportionately composed of persons of a particular race, color, national origin, sex, or handicap except...
-
A. Entry Doors
Do entry doors, connecting room doors, and interior doors (except doors to shallow closets) into and within all guestrooms and suites allow 32" clear passage width so persons who use wheelchairs...
-
407.2.1.1 Height
EXCEPTION: Existing call buttons and existing keypads shall be permitted to be located at 54 inches (1370 mm) maximum above the finish floor, measured to the centerline of the highest operable...
-
302.3 Openings
Openings in floor or ground surfaces shall not allow passage of a sphere more than ½ inch (13 mm) diameter except as allowed in 407.4.3, 409.4.3, 410.4, 810.5.3 and 810.10....
-
12183(a)(1)
) a failure to design and construct facilities for first occupancy later than 30 months after July 26, 1990, that are readily accessible to and usable by individuals with disabilities, except...
-
§ 36.105(d)(1)(ix)
(ix) The six-month “transitory” part of the “transitory and minor” exception in paragraph (f)(2) of this section does not apply to the “actual disability” or “record of” prongs of the definition...
-
211.2 Minimum Number
EXCEPTION: Where a single drinking fountain complies with 602.1 through 602.6 and 602.7, it shall be permitted to be substituted for two separate drinking fountains....
-
§ 36.304(d)(1)
(1) Except as provided in paragraph (d)(3) of this section, measures taken to comply with the barrier removal requirements of this section shall comply with the applicable requirements for...
-
11B-406.5.1 Location
Exception: Diagonal curb ramps shall comply with Section 11B-406.5.9....
-
7.4.9 Trail Facilities
Exception. ...
-
309.4 Operation
EXCEPTION: Gas pump nozzles shall not be required to provide operable parts that have an activating force of 5 pounds (22.2 N) maximum....
-
R103.1 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range. Advisory R103.1 Conventional Industry Tolerances....