(4) Ramp barriers. Each side of the ramp or bridge plate shall have barriers at least 2 inches high to prevent mobility aid wheels from slipping off.
Search Results "Railing"
Filters
Commonly Searched Documents
-
§ 38.83(c)(4) Ramp barriers
-
§ 38.125(b)(3) Emergency operation
(3) Emergency operation. The lift shall incorporate an emergency method of deploying, lowering to ground or station platform level with a lift occupant, and raising and stowing the...
-
§ 38.125(b)(9) Platform deflection
(9) Platform deflection. The lift platform (not including the entrance ramp) shall not deflect more than 3 degrees (exclusive of car roll) in any direction between its unloaded...
-
§ 38.125(b)(1) Design load
(1) Design load. The design load of the lift shall be at least 600 pounds. Working parts, such as cables, pulleys, and shafts, which can be expected to wear, and upon which the lift...
-
§ 38.95(b)(7) Platform gaps
(7) Platform gaps. Any openings between the lift platform surface and the raised barriers shall not exceed 5/8 inch wide. When the lift is at car floor height with the inner barrier...
-
11B-705.1.2.1 Platform edges
Detectable warning surfaces at platform boarding edges shall be 24 inches (610 mm) wide and shall extend the full length of the public use areas of the platform.
-
11B-247.1.2.1 Platform edges
Platform boarding edges shall have detectable warnings complying with Sections 11B-705.1.1 and 11B-705.1.2.1.
-
11B-810.6.1 Entrances
Where signs identify a station or its entrance, at least one sign at each entrance shall comply with Section 11B-703.2 and shall be placed in uniform locations to the maximum extent...
-
12162(a)(3)(A)(ii) a number of spaces
(ii) a number of spaces
-
§ 38.83(b)(13) Handrails
The handrails shall be capable of withstanding a force of 100 pounds concentrated at any point on the handrail without permanent deformation of the rail or its supporting structure....
-
T103 Definitions
These terms are: boarding platform, fixed route service (or fixed route), large transit entity, large non-rail vehicle, small non-rail vehicle, and non-rail vehicle....
-
T201.1 General
Non-rail vehicles purchased, leased or remanufactured by entities covered by the Americans with Disabilities Act (ADA) shall comply with the requirements in the Non-Rail Vehicle Guidelines...
-
T201 General
scoping requirements in Chapter 2 to the extent required by DOT’s implementing regulations for ADA-covered transportation vehicles, which, when revised, are required to use the 2016 Non-Rail...
-
Rehabilitation Engineering Research Center on Accessible Public Transportation
Mission The RERC on Accessible Public Transportation will research and develop methods to empower consumers, manufacturers, and service providers in the design and evaluation of...
-
§ 38.95(b)(13) Handrails
The handrails shall be capable of withstanding a force of 100 pounds concentrated at any point on the handrail without permanent deformation of the rail or its supporting structure....
-
T604 Stowage
[See subsections ...]
-
T704.3 Automated Announcement Systems
Automated systems for stop announcements and route identification announcements shall comply with T704.3.
-
T211 Wheelchair Securement Systems
[See subsections ...]
-
T211 Wheelchair Securement Systems
Wheelchair securement systems complying with the technical requirements in T603 must be provided at each wheelchair space. The Access Board received several comments on the proposed...
-
§ 38.97(a)
(a) Where provided, handrails or stanchions within the passenger compartment shall be placed to permit sufficient turning and maneuvering space for wheelchairs and other mobility...
-
§ 38.113(d)(3) Exception
(3) Exception. Where platform set-backs do not allow the horizontal gap or vertical alignment specified in paragraph (d) (1) or (2), platform or portable lifts complying with...
-
§ 38.111(a)(2)
(2) Single-level dining and lounge cars shall have at least one connecting doorway complying with §38.113(a)(2) of this part connected to a car accessible to persons using...
-
§ 38.83(c)(3) Ramp threshold
(3) Ramp threshold. The transition from roadway or station platform and the transition from vehicle floor to the ramp or bridge plate may be vertical without edge treatment up to 1/4...
-
§ 38.95(c)(4) Ramp barriers
(4) Ramp barriers. Each side of the ramp or bridge plate shall have barriers at least 2 inches high to prevent mobility aid wheels from slipping off.
