However, these fixed heights tables do not allow for independent transfer of patients who use wheeled mobility devices (WMD)....
Search Results "Patient with a Disability"
Filters
Commonly Searched Documents
-
How to Measure Transfer Surface Height
-
M101.2 Application
Sections M301 through M304 shall be applied to diagnostic equipment, based on the patient positions that the equipment supports, during patient transfer and diagnostic use....
-
6.1(4)(b)
(b) When patient bedrooms are being added or altered individually, and not as part of an alteration of the entire area, the altered patient bedrooms shall comply with 6.3, unless either:...
-
6.1(4)(a)
of the patient bedrooms that are being added or altered shall comply with 6.3....
-
19 Inch Low Height
support surfaces are contoured or upholstered for patient comfort or to support patient positioning during diagnostic procedures, the height of the transfer surface measured from the floor...
-
M305.4 Leg Supports
Leg supports shall provide a method of supporting, positioning, and securing the patient’s legs....
-
M305.2.6 Gripping Surfaces (Section-by-Section Analysis)
The MDE Advisory Committee explained that: [t]ransfer supports may contain elements to provide structural support or prevent patient entrapment....
-
5.4.6 Transfer Support Gripping Surface Cross Section and Clearances for M301, M302, and M305.2
Cross Section and Clearances for M301, M302, and M305.2 Description: This provision prescribes a cross-sectional profile of the transfer support sufficient to enable individuals with disabilities...
-
Within a Site: ADA Standard Section 206.2.2
Section 206.2.2 covers the scoping requirements for accessible routes within a site in the most current ADA Standards.
-
5.7.1.2 Lift Compatibility Clearance in Base for Imaging Equipment (M301)
Some imaging systems already use overhead lifts to assist patients. Overhead lifts are not feasible in the MR exam room due to the magnetic fields....
-
M301.2.1 Transfer Surface Height
Additionally these magnetic fields also preclude use of a patient’s mobility device in the exam room....
-
General: ADA Standard Section 805.1
Medical care facility and long-term care facility patient or resident sleeping rooms required to provide mobility features shall comply with 805....
-
§ 36.104 Definitions
Amend § 36.104 by revising the definition of ‘‘Disability’’ to read as follows: § 36.104 Definitions. * * * * * Disability....
-
§ 35.104 Definitions
Amend § 35.104 by revising the definition of ‘‘Disability’’ to read as follows: § 35.104 Definitions. * * * * * Disability....
-
How to Interact with Disabled People | Victoria Hamilton | TEDxYouth@Columbia
Victoria Hamilton (College of Charleston, ‘14) is changing how the world views disabled people in higher education....
-
M305.2.2 Length (Section-by-Section Analysis)
The Committee explained that the transfer support length provides the gripping surface for the patient to grasp or maintain balance while transferring....
-
5.4.7 Transfer Support Gripping Surface Clearance Recommendation for M301 and M302
Preamble Discussion: The Access Board is considering whether 1½ inches minimum clearance around the gripping surface would be appropriate for transfer supports on diagnostic equipment used by patients...
-
5.2.1.1 Transfer Surface Width
The transfer surface should be 28 inches wide minimum for equipment used by patients in a supine, side-lying, or prone position....
-
5.2.1 Transfer Surface Size Recommendations for M301
5.2.1 Transfer Surface Size Recommendations for M301 Description: The transfer surface is the part of the diagnostic equipment onto which patients who use mobility devices or aids transfer...
-
III-2.1000 General
Title III of the ADA prohibits discrimination against any "individual with a disability. " People commonly refer to disabilities or disabling conditions in a broad sense....
-
Sections 35.104 and 36.104—Definitions
Sections 35.104 and 36.104—Definitions The current title II and title III regulations include the definition of ‘‘disability’’ in regulatory sections that contain all enumerated definitions...
-
Standards that exclude an entire class of individuals with disabilities
Standards that exclude an entire class of individuals with disabilities "Blanket" exclusions of this kind usually have been established because employers believed them to be necessary...
-
c. Transfer Surface Size for Diagnostic Equipment Used by Patients in the Supine, Prone, or Side-lying Position
Four of the remaining commenters (manufacturers) felt that the transfer surface width should be decreased, while five (disability rights organizations, a medical association, and an individual...
-
§ 36.101(b) Broad coverage
The primary purpose of the ADA Amendments Act is to make it easier for people with disabilities to obtain protection under the ADA....
