Search Results "Adjustable Height Counter"

• State and Local Documents > Guidelines > 36 CFR Part 1191 ABA Accessibility Guidelines, Outdoor Developed Areas
  1013.4 Height

  Tent platforms shall be 19 inches (485 mm) high maximum measured from the clear ground space to the tent platform surface.

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  Transfer Surface Size – M301.2.2 Supine, Prone, or Side-Lying Position

  Transfer Surface Size – M301.2.2 Supine, Prone, or Side-Lying Position The issues were discussed and decided in the full committee meeting as follows: depth of 17 inches minimum...

• Federal Documents > Technical Assistance > ADAAG Manual
  Check-Out Areas [8.3]

  Check-Out Areas [8.3] Check-out counters at accessible lanes are held to a maximum surface height of 36 inches....

• Federal Documents > Preamble to Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment - Preamble
  M301.4.2 Clearance Around Base (Section-by-Section Analysis)

  This manufacturer indicated that its adjustable table does not have a six-inch minimum clearance when at its lowest position, but does meet the standard when the table is raised....

• State and Local Documents > Codes and Standards > 2013 California Standards for Accessible Design Pocket Guide
  11B-604.9.3 Height

  The height of water closets shall be 11 inches (279 mm) minimum and 17 inches (432 mm) maximum measured to the top of the seat....

• State and Local Documents > Codes and Standards > 2019 California Standards
  11B-604.9.3 Height

  The height of water closets shall be 11 inches (279 mm) minimum and 17 inches (432 mm) maximum measured to the top of the seat....

• State and Local Documents > Guidelines > Accessible Amusement Rides - A Summary of Accessibility Guidelines for Recreation Facilities
  Transfer Height

  Transfer Height The height of the transfer device must be between 14 and 24 inches above the load and unload area surface....

• Webinars, Videos, and Training > Product Demonstration or Information
  TAYLOR Point of Sale Mounting Stands Solutions
  

  We have created the world's first Point of Sale Smart Stand and using ADA Design Standards. It's a whole new reach of innovations in the Payments and Point of Sale Mounting Solutions...

• Webinars, Videos, and Training > Product Demonstration or Information
  Taylor ADA Blue-Lever Stands Intro.
  

  Introduction to Taylor ADA Blue Lever Stands for point of sale machines.

• Webinars, Videos, and Training > Product Demonstration or Information
  Taylor ADA Blue-Lever mounting Solutions
  

  This video shows some of the specifications of the Taylor ADA Blue-Lever POS mounting stands.

• Federal Documents > Preamble to Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment - Preamble
  M305.2.3 Height (Section-by-Section Analysis)

  In the MDE NPRM there was no specific requirement regarding the height of the transfer support, only that it be “within reach” of the patient (proposed M305.2.1)....

• State and Local Documents > Codes and Standards > 2012 Florida Accessibility Code
  703.2.5 Character Height

  703.2.5 Character Height....

• State and Local Documents > Codes and Standards > 2019 California Standards
  11B-703.8.9 Height above floor

  Heights of low resolution variable message sign characters shall comply with Table 11B-703.8.4, based on the size of the characters on the sign....

• Federal Documents > Standards > 1991 ADA Standards for Accessible Design
  8.3 Check-Out Areas

  At least one lane at each check-out area shall comply with 7.2(1). Any traffic control or book security gates or turnstiles shall comply with 4.13.

• Federal Documents > Standards > ABA Accessibility Standard for GSA Facilities Pocket Guide
  703.2.5 Character Height

  Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter "I"....

• State and Local Documents > Codes and Standards > 2012 Texas Accessibility Standards
  703.2.5 Character Height

  Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter "I"....

• Additional Access Publications > Ideas from Green Mountain Ranch : With Over 200 Green and Universal Design Elements
  Master Bath

  Unglazed ceramic mosaic tile for slip resistance Sink adaptable to a seated position Reinforcement for ceiling lift from the bed to the bathtub and...

• Federal Documents > Standards > 2010 ADA Standards
  Security Glazing: ADA Standard Section 904.6

  Where counters or teller windows have security glazing to separate personnel from the public, a method to facilitate voice communication shall be provided....

• Federal Documents > Standards > ABA Accessibility Standard for GSA Facilities Pocket Guide
  F232.5 Visiting Areas

  Visiting areas shall comply with F232.5.

• State and Local Documents > Codes and Standards > 2013 California Standards for Accessible Design Pocket Guide
  11B-232.5 Visiting areas

  Visiting areas shall comply with Section 11B-232.5.

• State and Local Documents > Codes and Standards > 2016 California Standards for Accessible Design Pocket Guide - Eff. Jan. 1, 2017
  11B-232.5 Visiting areas

  Visiting areas shall comply with Section 11B-232.5.  

• State and Local Documents > Codes and Standards > 2019 California Standards
  11B-232.5 Visiting areas

  Visiting areas shall comply with Section 11B-232.5.

• State and Local Documents > Codes and Standards > 2012 Texas Accessibility Standards
  232.5 Visiting Areas

  Visiting areas shall comply with 232.5.

• State and Local Documents > Codes and Standards > 2012 Florida Accessibility Code
  232.5 Visiting Areas

  232.5 Visiting Areas. Visiting areas shall comply with 232.5.