address access to sidewalks, streets, and other pedestrian facilities, provide requirements for pedestrian access routes, including specifications for route width, grade, cross slope, surfaces...
Search Results "Ground Surface"
Filters
Commonly Searched Documents
-
Shared Use Paths: ADA Standard Section 2.
-
11B-609.3 Spacing
Section 11B-609.9 the space between the walls and the grab bar shall be 1½ inches (38 mm) minimum for a distance of 6 inches on either side of the inside corner between two adjacent wall surfaces...
-
Expert opinion on the current knowledge
None of the research identified described how well individuals are able to overcome physical barriers in between the wheelchair and target surfaces. ...
-
11B-403.5.1 Clear width
Except as provided in Sections 11B-403.5.2 and 11B-403.5.3, the clear width of walking surfaces shall be 36 inches (914 mm) minimum. Exceptions: 1. ...
-
Grab Bars
Grab bars and any wall or other surfaces adjacent to grab bars must have rounded edges and are not allowed to have sharp or abrasive surfaces....
-
11B-705.1.2.3 Islands or cut-through medians
cut-through less 2 inches (51 mm) maximum on each side, placed at the edges of the pedestrian island or cut-through median, and shall be separated by 24 inches (610 mm) minimum of walking surface...
-
404 Doors, Doorways, and Gates
series (404.2.6) clarify the height of door and gate hardware and add an exception for gates at pools, spas, and hot tubs (404.2.7) revise an exception for door and gate surface...
-
Chapter 4: Accessible Routes
Chapter 4 contains technical requirements for accessible routes (402) and the various components of such routes, including walking surfaces (403), doors, doorways and gates (404), ramps...
-
11B-406.5.12 Detectable warnings
width of the curb ramp (exclusive of flared sides) and shall extend either the full depth of the curb ramp or 24 inches (610 mm) deep minimum measured from the back of the curb on the ramp surface...
-
M303.2.6 Edge Protection (Section-by-Section Analysis)
Protection), the final rule requires platforms with wheelchair spaces that are raised more than 1½ inches in height to provide a minimum 2-inch-high edge protection, measured from the surface...
-
Amusement Ride Seats Designed for Transfer
When greater distances are required for transfer, consideration should be given to providing gripping surfaces, seat paddings, and avoiding sharp or protruding objects....
-
Curb Ramps and Blended Transitions (R309.4) (Section-by-Section Analysis)
Detectable warning surfaces are not required on curb ramps and blended transitions that connect the access aisle to the sidewalk, including where the sidewalk is at the same level as the...
-
F. Check-In Areas
If a permanent reception counter is used for check in, make sure to provide a writing surface at an accessible height for people who use a wheelchair, scooter, or other mobility device....
-
2. Referenced Documents
Guide for Conducting Subjective Pavement Ride Quality Ratings E2133 Standard Test Method for Using a Rolling Inclinometer to Measure Longitudinal and Transverse Profiles of a Traveled Surface...
-
§ 38.159(b)(7) Platform gaps
Any openings between the platform surface and the raised barriers shall not exceed 5/8 inch (16 mm) in width....
-
11B-406.5.12 Detectable warnings
width of the curb ramp (exclusive of flared sides) and shall extend either the full depth of the curb ramp or 24 inches (610 mm) deep minimum measured from the back of the curb on the ramp surface...
-
11B-406.5.12 Detectable warnings
width of the curb ramp (exclusive of flared sides) and shall extend either the full depth of the curb ramp or 24 inches (610 mm) deep minimum measured from the back of the curb on the ramp surface...
-
11B-705.1.2.3 Islands or cut-through medians
cut-through less 2 inches (51 mm) maximum on each side, placed at the edges of the pedestrian island or cut-through median, and shall be separated by 24 inches (610 mm) minimum of walking surface...
-
THREATS AND HAZARDS IN NEW YORK CITY
An earthquake is the sudden, rapid shaking of the ground caused by two blocks of earth slipping past each other beneath the surface....
-
Stanley FBB 266 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
clear 90° Equipped with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface...
-
Stanley FBB 268 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
clear 90° Equipped with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface...
-
Stanley FBB 264 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
clear 90° Equipped with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface...
-
Stanley FBB 269 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
clear 90° Equipped with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface...
-
11B-220.2 Point-of-sale devices
point-of-sale devices are provided at check stands and sales and service counters, they shall comply with Section 11B-707.9.1, and shall also comply with Sections 11B-707.2 _|Clear Floor or Ground...
