requirements for alterations that will threaten or destroy the historic significance of qualified historic buildings and facilities as defined in 4.1.7(1)(a) of the Uniform Federal Accessibility Standards...
Search Results "Applicable Standard"
Filters
Commonly Searched Documents
-
12204(c)(1) In general
-
D5
[ADA Standards §§ 4.1.6(3)(d)(ii), 4.13.8] Yes No If No, replace threshold with one with beveled sides or add a sloped insert....
-
K4
[ADA Standards § 5.5] Yes No...
-
M5
[ADA Standards §§ 4.1.6(3)(d)(ii); 4.13.8] Yes No If No, replace threshold with one with beveled sides or add a sloped insert....
-
D.1. - How does Section 508 affect the requirements development phase of an acquisition?
Section 508 requires agencies to take additional considerations into account when defining their needs for EIT – namely the Access Board’s standards....
-
1c
[ADA Standards 4.21.2] Yes __ No __ N/A __ Comments: ________________________________________...
-
Flange way gap
(DOT ADA Standard 810.10.)...
-
I1a
[ADA Standards § 4.31.2, Fig. 44 (a)] Yes No...
-
D4
[ADA Standards § 4.13.6, Fig. 25] Yes No If No, leave the door propped open or find another accessible entrance....
-
301.1 Scope
Chapter 3 shall apply to ICT where required by 508 Chapter 2 (Scoping Requirements), 255 Chapter 2 (Scoping Requirements), and where otherwise referenced in any other chapter of the 508 Standards...
-
4.17.4 Toe Clearances
In standard stalls, the front partition and at least one side partition shall provide a toe clearance of at least 9 in (230 mm) above the floor....
-
4.17.4 TOE CLEARANCES
In standard stalls, the front partition and at least one side partition shall provide a toe clearance of at least 9 in (230 mm) above the floor....
-
Stability or Stable Surface
stable surface is one that remains unchanged by contaminants or applied force, so that when the contaminant or force is removed, the surface returns to its original condition (2010 ADA Standards...
-
§35.150 Existing facilities (Section-by-Section Analysis)
Congress intended the "undue burden" standard in title II to be significantly higher than the "readily achievable" standard in title III....
-
Social Security Disability Benefits Guide
We’ll walk you through each step of the process, and tell you what to expect during each stage of your Social Security disability application....
-
DO-IT Center
Promote the application of universal design to physical spaces, information technology, instruction, and services....
-
disAbility Solutions for Independent Living, Inc. (dSIL) - Daytona Beach, FL
The BOD promotes the independence of people with disabilities through empowerment and the support of Independent Living Services. dSIL promotes the application of all disability rights laws...
-
502.3.1 Object Information (Section-by-Section Analysis)
It is also consistent with existing 508 Standards § 1194.21(d), but more explicitly provides for the user to be able to change data values, not just read them....
-
502.2.1 User Control of Accessibility Features (Section-by-Section Analysis)
This provision would be new to the 508 Standards and 255 Guidelines, though it draws on the prohibition in § 1194.21(b) of the existing 508 Standards against disrupting or disabling accessibility...
-
Accessible Routes in Dwelling Units with Mobility Features
The 2010 Standards at sections 233.3.1.1, 809.1, 809.2, 809.2.1, and 809.4 will require all spaces and elements within dwelling units with mobility features to be on an accessible route....
-
Registered Accessibility Specialist (RAS) Bulletin RAS 2014-04 Signs - Exit Doors
However, a RAS has no authority to require compliance with TAS 216.4.1 based on RAS Bulletin 2012-01 since a referenced standard (ICC/IBC) dictates the location of exit passageway, exit...
-
5.7.1.1 Lift Compatibility Clearance in Base for Stretchers (M301)
The change harmonizes this provision with the international standards. IEC 60601-2-52 provides requirements for stretchers and includes a lift clearance at the 39 inch width....
-
Facility
Facilities must comply with all 2010 ADA Standards for Accessible Design for new construction and remodeling projects....
-
Door Hardware
The ANSI standard also recognizes this point....
