DOJ’s ADA regulations include requirements that may impact non-fixed elements, such as providing accessible medical equipment, including examination tables and chairs, to provide persons...
Search Results "Non-Positive Shut Off"
-
Furnishings and Equipment
-
Scope: ADA Standard Section 201.1
Section 201 discusses the scope of the ADA Standards.
-
11B-233.3.1.2 Residential dwelling units with adaptable features
In buildings with three or more residential dwelling units, adaptable residential dwelling units complying with Sections 11B-809.6 through 11B-809.12. shall be provided as required...
-
11B-233.3.1.2 Residential dwelling units with adaptable features
In buildings with three or more residential dwelling units, adaptable residential dwelling units complying with Sections 11B-809.6 and shall be provided as required by Sections...
-
M305.2.8 Fittings
Transfer supports shall not rotate within their fittings when in place for transfer.
-
M305.2.7 Clearance
Clearance between the transfer support gripping surface and adjacent surfaces or obstructions shall be 1 ½ inches (38 mm) minimum.
-
M305.2.7 Clearance (Section-by-Section Analysis)
In the MDE NPRM, the Access Board did not provide any specific requirements for clearances around the transfer support. However, in the preamble to the MDE NPRM the Access Board...
-
M305.2.3 Fittings
Transfer supports shall not rotate within their fittings.
-
5.2.1.1 Transfer Surface Width Recommendations for M301
Transfer Surface Width Recommendations for M301 The Committee recommends a transfer surface of 28 inches minimum width for equipment used by patients in a supine, side-lying, or prone position...
-
M302.2.2 Sunset
The low transfer position height, Item A of M302.2.1, shall cease to have effect on [Insert date 5 years after date of publication in the Federal Register]. [sic]...
-
H. Chapter 7: Communication Features
Chapter 7 in the 2016 Non-Rail Vehicle Guidelines establishes technical requirements for characters on signs, the International Symbol of Accessibility, and vehicular announcement systems...
-
Aqua Creek Scout Pool and Spa Lift Informational Video
The Scout pool and spa lift is an ADA Compliant pool lift designed for in-ground anchoring. This lift is designed to be able to fit into many existing anchor systems.
-
S.R. Smith PAL Pool Lift Video 4: Resolution
Removing and replacing key components of your PAL pool lift such as the control box, actuator, actuator cable, motor cable, motor assembly and the gears. Please complete PAL Pool...
-
S.R. Smith PAL Pool Lift Video 1: Installation and Operation
This video gives an overview of how to unpack, assemble, use and maintain your PAL Pool Lift.
-
S.R. Smith PAL Pool Lift Video 3: Advanced Troubleshooting
Advanced troubleshooting procedures for your PAL pool lift. Please watch PAL Pool Lift Level 1: Basic Troubleshooting before viewing this video.
-
S.R. Smith PAL Pool Lift Video 2: Basic Troubleshooting
Basic troubleshooting methods for your PAL pool lift. When troubleshooting your PAL lift, start with this video.
-
Costs and Benefits
Orders 12866 and 13563, the Access Board prepared a final regulatory assessment (Final RA) to assess the likely costs and benefits of new or revised accessibility requirements in the 2016 Non-Rail...
-
M305.3.1.3 Vertical Position
The length of the gripping surface on vertical standing supports shall be 18 inches (455 mm) minimum.
-
M305.3.2.2 Vertical Position
The height of the lowest end of the gripping surface on vertical standing supports shall be 34 inches (865 mm) minimum and 37 inches (940 mm) maximum above the standing surface.
-
M305.3.2 Vertical Position
Where the support is vertical, it shall be 18 inches (455 mm) minimum in length and the bottom end of the support shall be 34 inches (865 mm) high minimum and 37 inches (940 mm) high...
-
c. Transfer Surface Size for Diagnostic Equipment Used by Patients in the Supine, Prone, or Side-lying Position
The MDE NPRM proposed a transfer surface size for diagnostic equipment used in the supine, prone, or side-lying position of 30 inches wide and 15 inches deep minimum (proposed M301.2.2)....
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the...
-
M305.2.4 Cross Section
Transfer supports shall have a cross section complying with 305.2.4.1 or 305.2.4.2.
-
M305.2.3 Height
During use, the tops of transfer support gripping surfaces shall be 6 inches (150 mm) minimum and 19 inches (485 mm) maximum higher than the top of the associated uncompressed...
