EXCEPTION: Where shoulder-to-shoulder companion seating is not operationally or structurally feasible, compliance with this requirement shall be required to the maximum extent practicable...
Search Results "Maximum Reach Depth"
-
1002.4.7.1 Shoulder-to-Shoulder Seating
-
1002.4.7.1 Shoulder-to-Shoulder Seating
EXCEPTION: Where shoulder-to-shoulder companion seating is not operationally or structurally feasible, compliance with this requirement shall be required to the maximum extent practicable...
-
1002.4.7.1 Shoulder-to-Shoulder Seating
EXCEPTION: Where shoulder-to-shoulder companion seating is not operationally or structurally feasible, compliance with this requirement shall be required to the maximum extent practicable...
-
11B-810.4 Bus signs
In addition, to the maximum extent practicable, bus route identification signs shall comply with Section 11B-703.5.5 _|Character Height|_....
-
11B-810.4 Bus signs
In addition, to the maximum extent practicable, bus route identification signs shall comply with Section 11B-703.5.5 _|Character Height|_....
-
Gaps: ADA Standard Section 1002.4.3
are at rest in the load and unload position, the vertical difference between the floors shall be within plus or minus 5/8 inches (16 mm) and the horizontal gap shall be 3 inches (75 mm) maximum...
-
11B-104.1 Dimensions
Dimensions that are not stated as "maximum" or "minimum" are absolute. Advisory 11B-104.1 Dimensions. This section clarifies the dimensioning conventions used in this chapter. ...
-
11B-104.1 Dimensions
Dimensions that are not stated as “maximum” or “minimum” are absolute. Advisory 11B-104.1 Dimensions. This section clarifies the dimensioning conventions used in this chapter. ...
-
11B-104.1 Dimensions
Dimensions that are not stated as “maximum” or “minimum” are absolute. Advisory 11B-104.1 Dimensions. This section clarifies the dimensioning conventions used in this chapter....
-
Alterations: ADA Standard Section 202.3
Section 202.3 covers the most current requirements for alterations in existing building and facilities.
-
1 - Design and drawing
If the value is a minimum or maximum or a range, this fact may not be communicated to the contractor, who may think that there is a tolerance ed....
-
11B-202.5 Alterations to qualified historic buildings and facilities
(3)(i) Alterations to historic properties shall comply, to the maximum extent feasible, with the provisions applicable to historic properties in the design standards specified in §35.151...
-
11B-202.5 Alterations to qualified historic buildings and facilities
(3)(i) Alterations to historic properties shall comply, to the maximum extent feasible, with the provisions applicable to historic properties in the design standards specified in §35.151...
-
11B-306.2.2 Maximum depth
Toe clearance shall extend 25 inches (635 mm) maximum under an element....
-
11B-306.2.2 Maximum depth
Toe clearance shall extend 25 inches (635 mm) maximum under an element....
-
1008.4.2 Clear Floor or Ground Space
The following table provides guidance on reach ranges for children seated in wheelchairs. These dimensions apply to either forward or side reaches....
-
1008.4.2 Clear Floor or Ground Space
The following table provides guidance on reach ranges for children seated in wheelchairs. These dimensions apply to either forward or side reaches....
-
11B-604.8.1.1 Size
Wheelchair accessible compartments shall be 60 inches (1524 mm) wide minimum measured perpendicular to the side wall, and 56 inches (1422 mm) deep minimum for wall hung water closets...
-
11B-604.8.1.1 Size
Wheelchair accessible compartments shall be 60 inches (1524 mm) wide minimum measured perpendicular to the side wall, and 56 inches (1422 mm) deep minimum for wall hung water closets...
-
F104.1 Dimensions
Dimensions that are not stated as "maximum" or "minimum" are absolute....
-
104.1 Dimensions
Dimensions that are not stated as "maximum" or "minimum" are absolute....
-
104.1 Dimensions
Dimensions that are not stated as "maximum" or "minimum" are absolute....
-
Card Catalogs and Magazine Displays [8.4]
Requirements for fixed counters and tables [4.32] specify a surface height (34 inches maximum) and knee clearance below appropriate for extended use as a writing/work surface....
-
R405.2.2 Maximum Depth
R405.2.2 Maximum Depth. Toe clearance shall extend 635 mm (2.1 ft) maximum under an element....