(j) EXCEPTION: In alteration work, if compliance with 4.1.6 is technically infeasible, the alteration shall provide accessibility to the maximum extent feasible....
Search Results "Maximum Reach Depth"
Filters
Commonly Searched Documents
-
4.1.6(1)(j) EXCEPTION
-
M201.2 General Exception (Section-by-Section Analysis)
Any equipment falling under this exception must comply with the provision(s) in question to the maximum extent practicable, and must fully comply with all other provisions not utilizing...
-
Section 35.151(b)(3) Alterations to historic facilities (Section-by-Section Analysis)
Currently, the regulation provides that alterations to historic facilities shall comply to the maximum extent feasible with section 4.1.7 of UFAS or section 4.1.7 of the 1991 Standards....
-
Salad Bars and Buffet Counters
Salad Bars and Buffet Counters Recommendations: The standard reach range should be considered in the design of built-in salad bars although not all portions are required to be within...
-
1. General Exception
Section 510 of the Rehabilitation Act requires the MDE Standards to provide independent access “to the maximum extent possible.”...
-
Door King Inc. 1520/1524 Stand Alone Card Readers
The model 1520 provides users with a full feature single door stand-alone access control system. The 1520 is available with a built-in proximity card reader (DK Prox, AWID or HID) or...
-
Alterations: Alternate Stalls
Alternate designs in ADAAG Figure 30(b) allow narrower stall widths while requiring greater depth....
-
Access Board: Reach Ranges
This video is part of a longer animation produced by the U.S. Access Board. View the animation video in its entirety on the Access Board's website...
-
Figure 904.4 (Exception) Alteration of Sales and Service Counters – Drawing from the U.S. Access Board
-
Re: Section 307 Protruding Objects
Could you please direct me to the section in the code indicates that an 8" deep shelf at 40"-48" AFF is code compliant as stated? Thank you in advance!
-
Alterations Affecting Primary Function Areas: ADA Standard Section 202.4
Section 202.4 covers the most current ADA Standards for alterations affecting primary function area.
-
308.3.1 Automatic Trash Can Height
-
H13
H13. Is the operating control (switch, lever, button, or pull) of at least one of each type of dispenser or built-in equipment no higher than 54 inches above the floor (if there is...
-
I1a
I1a. For a side approach (clear floor space at least 30 inches long x 48 inches wide), is the coin slot no higher than 54 inches above the floor? [ADA Standards § 4.31.2, Fig. 44...
-
M14
M14. Is the operating control (switch, lever, button, or pull) for each type of dispenser or built-in equipment no higher than 54 inches above the floor (if there is clear floor...
-
A4.31.3 MOUNTING HEIGHT
In localities where the dial-tone first system is in operation, calls can be placed at a coin telephone through the operator without inserting coins. The operator button is located...
-
11B-1008.4.2 Clear floor or ground space
The reach ranges are appropriate for use with those play components that children seated in wheelchairs may access and reach....
-
1008.4.2 Clear Floor or Ground Space
The following table provides guidance on reach ranges for children seated in wheelchairs. These dimensions apply to either forward or side reaches....
-
11B-1008.4.2 Clear floor or ground space
The following table provides guidance on reach ranges for children seated in wheelchairs. These dimensions apply to either forward or side reaches....
-
11B-1008.4.2 Clear floor or ground space
The following table provides guidance on reach ranges for children seated in wheelchairs. These dimensions apply to either forward or side reaches....
-
Exception [1013.1, Exception]
When a condition for exception does not permit full compliance with a specific provision in the technical requirements for tent pads and tent platforms, the tent pads and tent...
-
How is “technical infeasibility” determined in an alteration?
Determining “technical infeasibility” requires a site-specific assessment of constraints or complications in relation to the planned scope of work. The term, as defined in the...
-
§40.3(a)
If the design of a structure commenced prior to that date, the standards shall be made applicable to the maximum extent practicable, as determined by the head of the department, agency,...
