Section 505.10 covers the current ADA Standards for handrail extensions.
Search Results "9-1-1 Service"
Filters
Commonly Searched Documents
-
Handrail Extensions: ADA Standard Section 505.10
-
1.9.1.8 Adopting agency identification
ETA Editor's Note The remainder of California Building Code Chapter 1 is not adopted by Division of the State Architect - Access Compliance (DSA-AC), has been omitted....
-
1607.9.2 Grab bars, shower seats and accessible benches
[DSA-AC & HCD 1-AC] See Chapter 11A, Section 1127A.4, and Chapter 11B, Sections 11B-609.8, 11B-610.4 and 11B-903.6, for grab bars, shower seats and dressing room bench seats, as applicable...
-
II. COMPLIANCE WITH TITLE III OF THE ADA
Web Accessibility Conformance Timeline: H&R Block shall ensure full and equal enjoyment of the goods, services, facilities, privileges, advantages, and accommodations provided by and...
-
11B-202.4 Path of travel requirements in alterations, additions and structural repairs
Widening doors. 9. Installing offset hinges to widen doorways. 10. Eliminating a turnstile or providing an alternative accessible route. 11....
-
Notes
Notes PP The Advisory Committee spent considerable time trying to: (1) choose appropriate language for describing this population subgroup; and (2) find explicit parameters for what constitutes...
-
III-3.1000 General
Individuals with disabilities may not be denied full and equal enjoyment of the "goods, services, facilities, privileges, advantages, or accommodations" offered by a place of public accommodation...
-
1007.2 Accessible Routes
EXCEPTIONS: 1. Playing surfaces shall not be required to comply with 302.2. 2....
-
Grab Bar Cross Sections
The proposed rule specified 1 ¼ to 1 ½ circular cross sections....
-
1018.1 General
EXCEPTIONS: 1....
-
QUESTION: WHEN DO THE REQUIREMENTS OF SECTION 37.42 BEGIN TO APPLY?
standard and other requirements of section 37.42(a) apply to stations that are approved for entry into final design or that begin construction or alteration of platforms on or after February 1,...
-
1018.1 General
EXCEPTIONS: 1....
-
11B-505.6 Gripping surface
Where provided, horizontal projections shall occur 1½ inches (38 mm) minimum below the bottom of the handrail gripping surface. Exceptions: 1. ...
-
Mockett PCS5/M/4E Large Rectangular Power Grommet
Perhaps best of all, it has a very low profile, just 1/8" above work surface. Fastens securely from underneath....
-
Summary of Significant Changes
For purposes of this requirement, a “large transit entity” is defined as a provider of public transportation that operates 100 or more buses in annual maximum service for all fixed route...
-
Pilot Rock Bench B110C with Full-length Grab Bar
SPECIFICATIONS: FRAME: All welded steel frame fabrication: seat/back support channel is die-formed from 1/8" thick (11 ga.) steel, frame post and portable/surface mount foot are made using...
-
Pilot Rock CN-R/D Trash Receptacle
Specifications: Model CN-R/D Trash Receptacle is fabricated from a single piece of 3/4-#9 expanded steel (diamond holes) and reinforced with 10 ga. top and bottom rings and die formed...
-
Background:
Department of Transportation’s (DOT) Americans with Disabilities Act (ADA) regulation at 49 CFR § 37.43(a)(1), provides that when a public entity “alters an existing facility or a part of...
-
3104.2 Separate structures
Exceptions: 1. Buildings on the same lot in accordance with Section 503.1.2 shall be considered a single structure. 2. ...
-
404.2.5 Thresholds
Thresholds, if provided at doorways, shall be 1/2 inch (13 mm) high maximum. Raised thresholds and changes in level at doorways shall comply with 302 and 303....
-
404.2.5 Thresholds
Thresholds, if provided at doorways, shall be 1/2 inch (13 mm) high maximum. Raised thresholds and changes in level at doorways shall comply with 302 and 303....
-
410.6.3.1 PSTN (Section-by-Section Analysis)
with real-time two-way voice communication interoperates with the publicly switched telephone network (PSTN), real-time text conform to TIA 825-A (incorporated by reference in 508 Chapter 1...
-
4.10.9 Floor Plan of Elevator Cars
The clearance between the car platform sill and the edge of any hoistway landing shall be no greater than 1‒1/4 in (32 mm)....
-
4.10.9 FLOOR PLAN OF ELEVATOR CARS
The clearance between the car platform sill and the edge of any hoistway landing shall be no greater than 1-1/4 in (32 mm)....
