Where two or more bathrooms are provided, when a bathtub is installed in the first bathroom in compliance with Section 11B-809.10.5 and a shower compartment is provided in a subsequent bathroom...
Search Results "ADA Compliance"
-
11B-809.10.2 Number of complying bathrooms and fixtures
-
11B-233.3.4.2 Alterations to individual residential dwelling units
[2010 ADAS] 233.3.4.2 Alterations to Individual Residential Dwelling Units. ...
-
7.11(a) Collective Bargaining Agreements
7.11(a)Collective Bargaining Agreements Labor unions are covered by the ADA and have the same obligation as the employer to comply with its requirements....
-
B. Scoping Requirements for Units with Communication Features
Scoping Requirements for Units with Communication Features The ADA and ABA Accessibility Guidelines require at least 2 percent of the residential dwelling units in a facility to provide...
-
Attachment A
Equal Employment Opportunity Commission under title I of the Americans with Disabilities Act (ADA)....
-
11B-233.3.4.2 Alterations to individual residential dwelling units
[2010 ADAS] 233.3.4.2 Alterations to Individual Residential Dwelling Units. ...
-
11B-224.7.2 Multi-bedroom housing units with adaptable features
ETA Editor's Note The following Access Board Note was taken from ADA Title II §35.151(f) New Construction and Alterations; Housing at a Place of Education, and ADA Title III §36.406(e...
-
11B-104.1.1 Construction and manufacturing tolerances
It will also more often produce an end result of strict and literal compliance with the stated requirements and eliminate enforcement difficulties and issues that might otherwise arise....
-
11B-104.1.1 Construction and manufacturing tolerances
It will also more often produce an end result of strict and literal compliance with the stated requirements and eliminate enforcement difficulties and issues that might otherwise arise....
-
I. TITLE I: AN OVERVIEW OF LEGAL REQUIREMENTS
TITLE I: AN OVERVIEW OF LEGAL REQUIREMENTS This chapter of the manual provides a brief overview of the basic requirements of Title I of the ADA....
-
§382.51(a)(3)
inter-terminal transportation, including, but not limited to, moving sidewalks, shuttle vehicles and people movers, comply with applicable requirements of the Department of Transportation's ADA...
-
1630.9(c)
(c) A covered entity shall not be excused from the requirements of this part because of any failure to receive technical assistance authorized by section 506 of the ADA, including any failure...
-
11B-407.3.5 Door delay
[2010 ADAS] 407.3.5 Door Delay. Elevator doors shall remain fully open in response to a car call for 3 seconds minimum....
-
T201.1 General
Non-rail vehicles purchased, leased or remanufactured by entities covered by the Americans with Disabilities Act (ADA) shall comply with the requirements in the Non-Rail Vehicle Guidelines...
-
Does a wheelchair need brakes in order to use the transportation service?
The DOT ADA regulations’ definition of a wheelchair does not include a requirement for brakes or any other equipment....
-
Does a wheelchair need brakes in order to use the transportation service?
The DOT ADA regulations’ definition of a wheelchair does not include a requirement for brakes or any other equipment....
-
1i
[ADA Stds. 4.21.7] Yes __ No __ N/A __ Comments: ___________________________________________...
-
E. Smoking Rooms
[ADA Stds. 9.1.4] Yes __ No __ N/A __ Comments: ___________________________________________...
-
D. Sign Height
[ADA Stds. 4.6.4] Yes __ No __ N/A __ Comments: ___________________________________________...
-
5. Grab Bar
[ADA Stds. 4.23.8; 4.20.4] Yes __ No __ N/A __ Comments: _____________________________________...
-
1. Clear Width
[ADA Stds. 9.2.2(3); 4.13.5] Yes __ No __ N/A __ Comments: _____________________________________...
-
H5
[ADA Standards §§ 4.1.6(3)(d)(ii), 4.13.8] Yes No NA If No, replace threshold with one with beveled sides or add a sloped insert....
-
D5. Raised Threshold
[ADA Stds 4.1.6(3)(d)(ii), 4.13.8] Yes _____ No _____ If No, replace threshold with one with beveled sides or add sloped insert to threshold....