[ADA Standards §§ 4.23.7; 4.27.2; 4.2.5 and Fig 5; 4.2.6 and Fig 6] Yes No...
Search Results "Electroacoustic Performance Standards"
-
H12
-
§ 36.303(g)(4)(ii)
section by using the existing assistive listening receivers that the public accommodation is already required to provide at its movie theaters in accordance with Table 219.3 of the 2010 Standards...
-
Can curbs be used to indicate areas with less than 80” of vertical clearance?
The standards specify a maximum height (27”) for the leading edge of barriers so they are within cane sweep, but a minimum height is not specified....
-
§1193.51(d) TTY connectability
Products which provide a function allowing voice communication and which do not themselves provide a TTY functionality shall provide a standard non-acoustic connection point for TTYs....
-
TTY
Machinery or equipment that employs interactive text based communications through the transmission of coded signals across the standard telephone network....
-
§ 35.151(e) Social service center establishments.
center establishments that provide either temporary sleeping accommodations or residential dwelling units that are subject to this section shall comply with the provisions of the 2010 Standards...
-
14) Carpet and carpet tile
14) Carpet and carpet tile ADAAG: Same standards for carpet and carpet tile: maximum pile height of 1/2" (§4.5.3). UFAS: Carpet must have maximum pile height of 1/2"....
-
ACCESSIBLE MEANS OF EGRESS
[2010 ADA Standards 106.5] Accessible Means of Egress....
-
Use Zone
The ground level area beneath and immediately adjacent to a play structure or play equipment that is designated by ASTM F 1487 (incorporated by reference, see "Referenced Standards" in Chapter...
- Regulatory Task Forces - The Mayer-Rothschild Foundation
- International Code Council (ICC): Become an ICC Certified Accessibility Inspector/Plans Examiner
-
Section 1630.15(d) Defense To Not Making Reasonable Accommodation
demonstrate undue hardship pursuant to the ADA and this part, an employer must show substantially more difficulty or expense than would be needed to satisfy the “de minimis” title VII standard...
-
5.4.1.2 Transfer and Positioning Support Location Recommendations for Imaging Equipment with Transfer Surfaces
Minimum load bearing requirements for supports are found in international standards (e.g. risk management ISO 14971; IEC60601-1; and use of IEC60601-2-52.)...
-
II. Terms of Agreement
The XL Center Parties further agree that modifications to the XL Center must comply with the 2010 ADA Standards for Accessible Design (the 2010 Standards), See 28 CFR § 36.104 (defining...
-
Understanding the K League Structure and Promotion Paths in Modern Football Systems
Unlike closed franchise systems seen in some sports markets, the K League uses performance-based mobility....
-
M201.2 General Exception
Medical diagnostic equipment shall not be required to comply with one or more applicable requirements in the MDE Standards in the rare circumstances where compliance would alter diagnostically...
-
[A] BUILDING
The accessibility standards generally apply to buildings and facilities....
-
Sections 4.2 Through 4.35 (Preamble, Section-by-Section Analysis)
The technical specifications are the same as the 1980 version of ANSI A117.1 standard, except as noted in the text by italics....
-
New Construction and Alterations
New Construction and Alterations Businesses whose facilities were built or altered since the ADA went into effect must comply with the ADA Standards for Accessible Design so that the...
-
Accessible Miniature Golf Course Holes
Sections 239.2 and 1007.3 of the 2010 Standards require at least fifty percent (50%) of golf holes on miniature golf courses to be accessible, including providing a clear floor or ground...
-
6.11
6.11 Nothing in Section 6 of the Consent Order shall limit the placement of any additional wheelchair spaces required by state or local codes beyond those mandated under the ADA Standard...
-
12101(a)(5)
architectural, transportation, and communication barriers, overprotective rules and policies, failure to make modifications to existing facilities and practices, exclusionary qualification standards...
-
a. Federal Laws
This defense is not valid, however, if the Federal standard does not require the discriminatory action, or if there is a way that an employer can comply with both legal requirements....
-
243 Shooting Facilities with Firing Positions
243 Shooting Facilities with Firing Positions Sections 243 and 1010 of the 2010 Standards require an accessible turning space for each different type of firing position at a shooting...