Section 407.3.4 covers the current ADA Standards for door and signal timing of elevator reopening devices.
Search Results "Viewing Distance"
-
Door and Signal Timing: ADA Standard Section 407.3.4
-
11B-1002.5 Amusement ride seats designed for transfer
Where greater distances are required for transfers, providing gripping surfaces, seat padding, and avoiding sharp objects in the path of transfer will facilitate the transfer. ◼...
-
11B-407.3.4 Door and signal timing
car start to close shall be calculated from the following equation: T = D/(1.5 ft/s) or T = D/(457 mm/s) = 5 seconds minimum where T equals the total time in seconds and D equals the distance...
-
11B-407.3.4 Door and signal timing
car start to close shall be calculated from the following equation: T = D/(1.5 ft/s) or T = D/(457 mm/s) = 5 seconds minimum where T equals the total time in seconds and D equals the distance...
-
11B-1002.5 Amusement ride seats designed for transfer
Where greater distances are required for transfers, providing gripping surfaces, seat padding, and avoiding sharp objects in the path of transfer will facilitate the transfer. ◼...
-
6.7.1.2
Resting intervals complying with section 2.3 shall be provided at distances of no more than 50 feet (15 m) apart....
-
6.7.1.3
Resting intervals complying with section 2.3 shall be provided at distances of no more than 30 feet (9 m) apart....
-
Vision Lights: ADA Standard Section 404.2.11
Section 404.2.11 covers the current ADA Standards for vision lights on manual doors and gates.
-
End Note
This publication may also be viewed or downloaded from the TDLR website (www.license.state.tx.us)....
-
ETA Summary of ADAAG/CBC Signage Requirements
ADAAG/CBC Signage Requirements Click here to view/download the pdf version (1.22 MB)...
-
ETA Summary of ADA Signage Requirements
Summary of ADA Signage Requirements Click here to view/download the pdf version (162 KB)....
-
2. Using the Tape Measure
When measuring long distances, pull the tape tight to get an accurate measurement. The checklist will offer guidance for the specific measurement that is required....
-
DOT Response
In the Department's view, the ADA does not provide a statutory basis for requiring the expansion of the list of key stations, renovation of which for accessibility was to have been completed...
-
4.3.7 Clear Floor Space for Reaching
Reaching across the body will reduce the effective reach distance due to the reduced radius of reach....
-
Design of Shared Use Paths, Street Intersections, and Midblock Crossings
Sight Distance 1. Stopping Sight Distance a. Reaction Time b. Braking Distance c. Design Values 2. Criteria for Measuring Sight Distance a....
-
404.2.6 Doors in Series and Gates in Series
The distance between two hinged or pivoted doors in series and gates in series shall be 48 inches (1220 mm) minimum plus the width of doors or gates swinging into the space....
-
3. Toilet Centerline
Is the accessible toilet in each accessible guestroom bathroom centered 18" from the adjacent side wall, which is the distance that will permit a person with a mobility impairment to use...
-
A4.11.2 Other Requirements
Inclined stairway chairlifts, and inclined and vertical platform lifts (wheelchair lifts) are available for short-distance, vertical transportation of people with disabilities....
-
Section 4.9.4
• Section 4.9.4 of the 1991 Standards requires handrails at the bottom of stairs to continue to slope for a distance of the width of one tread beyond the bottom riser nosing and to further...
-
Location [§208.3]
A maximum travel distance is not specified in the Standards....
-
1.2.6
Allowing 20% of local variations to slope up to 10% seems reasonable for a distance of one foot....
-
11B-505.10.3 Bottom extension at stairs
At the bottom of a stair flight, handrails shall extend at the slope of the stair flight for a horizontal distance equal to one tread depth beyond the last riser nosing. ...
-
704.8 Allowable area of openings
TABLE 704.8 MAXIMUM AREA OF EXTERIOR WALL OPENINGSa Classification of opening FIRE SEPARATION DISTANCE (feet) 0 to 3 e,h Greater that 3 to 5b...
-
Abstract
Surfaces objectively measured as firm and stable would be allowed for unlimited distances....