11B-703.8.8 Line spacing. Low resolution VMS characters shall comply with Section 11B-703.5.9.
Search Results "Transit Sign"
-
11B-703.8.8 Line spacing
-
11B-703.8.10 Finish
11B-703.8.10 Finish. The background of low resolution VMS characters shall have a non-glare finish.
-
11B-703.8.2 Case
11B-703.8.2 Case. Low resolution VMS characters shall be uppercase.
-
11B-703.8.10 Finish
11B-703.8.10 Finish. The background of low resolution VMS characters shall have a non-glare finish.
-
11B-703.8.7 Character spacing
11B-703.8.7 Character spacing. Spacing shall be measured between the two closest points of adjacent low resolution VMS characters within a message, excluding word spaces. Low...
-
11B-703.8.5 Character width
11B-703.8.5 Character width. The uppercase letter “O” shall be used to determine the allowable width of all low resolution VMS characters of a font. Low resolution VMS characters...
-
11B-703.8.8 Line spacing
11B-703.8.8 Line spacing. Low resolution VMS characters shall comply with Section 11B-703.5.9.
-
11B-703.8.5 Character width
The uppercase letter “O” shall be used to determine the allowable width of all low resolution VMS characters of a font. Low resolution VMS characters shall comply with the pixel...
-
11B-703.8.10 Finish
The background of low resolution VMS characters shall have a non-glare finish.
-
11B-703.8.2 Case
Low resolution VMS characters shall be uppercase.
-
11B-703.8.8 Line spacing
Low resolution VMS characters shall comply with Section 11B-703.5.9.
-
11B-703.8.7 Character spacing
Spacing shall be measured between the two closest points of adjacent low resolution VMS characters within a message, excluding word spaces. Low resolution VMS character spacing shall...
-
R308.1.1.1 Dimensions
R308.1.1.1 Dimensions. Boarding and alighting areas shall provide a clear length of 2.4 m (8.0 ft) minimum, measured perpendicular to the curb or street or highway edge, and a clear...
-
E1-b
E1-b. Is the accessible route free of steps and abrupt level changes over 1/2 inch? Yes No Note: level changes between 1/4 inch and 1/2 inch should be beveled). [ADA...
-
Make Changes
Make Changes Use the 2010 ADA Standards for Accessible Design. Check whether local and state building codes require greater accessibility when alterations are undertaken.
-
7.4.6 Tread Obstacles
Tread obstacles on trails shall not exceed 2 inches (50 mm) in height measured vertically to the highest point. Where the trail surface is paved or is elevated above the natural...
-
E1-2. Accessible Route
E1-2. Is the accessible route free of steps and abrupt level changes over 1/2 inch (level changes between 1/4 inch and 1/2 inch should be beveled)? [ADA Stds 4.1.3(1), 4.3.8] Yes...
-
10.3.1(16)
(16) Where provided in below grade stations, escalators shall have a minimum clear width of 32 inches. At the top and bottom of each escalator run, at least two contiguous treads...
-
10.3.1(14)
(14) Where public address systems are provided to convey information to the public in terminals, stations, or other fixed facilities, a means of conveying the same or equivalent...
-
Changes in Level [4.5.2]
Vertical changes in level up to ¼ inch are permitted without treatment along accessible routes. Changes in level ¼ to ½ inch must be beveled with a slope no greater than 1:2. Changes...
-
§ 37.155 Factors in decision to grant an undue financial burden waiver
[See subsections ...]
-
§ 37.167(b)
(b) On fixed route systems, the entity shall announce stops as follows:
-
§ 37.153 FTA waiver determination
[See subsections ...]
-
Section 37.147 FTA Review of Plans
Section 37.147 FTA Review of Plans This provision spells out factors FTA will consider in reviewing each plan, including whether the submission is complete, whether the plan...