If level-entry boarding, portable or platform lifts, ramps or bridge plates meeting the applicable requirements of this section are provided on station platforms or other stops required...
Search Results "Ramp Surface"
-
§ 38.95(a)(2) Exception
-
Picnic Tables [1011.2 and 1011.4]
The number of wheelchair spaces that must be provided at each table is based on the usable table surface perimeter....
-
Utilities at Recreation Sites
When the surface is unpaved or not built with boards, grades up to 1:33 (3 percent) are allowed if needed for proper drainage....
-
11B-812.7.2 Marking
The color of the borderlines, hatched lines, and letters shall contrast with that of the surface of the access aisle....
-
Grab Bars: ADA Standard Section 1009.4.5
The top of the gripping surface shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above transfer walls....
-
11B-809.10.5.1 Clear floor space
The edge of the clear floor space shall be flush with the control wall surface....
-
Unobstructed: ADA Standard Section 308.3.1
Section 308.3.1 covers the current ADA Standards for unobstructed side reach.
-
11B-812.7.2 Marking
The color of the borderlines, hatched lines, and letters shall contrast with that of the surface of the access aisle....
-
11B-809.10.5.1 Clear floor space
The edge of the clear floor space shall be flush with the control wall surface....
-
R302.2 Components
Curb ramps and blended transitions complying with R302.7 and R304; 5. Ramps complying with R407; 6....
-
City of XXX – ADA Transition Plan
Issue Solution Target Date Person Responsible Cost Estimate Source of Fund South Entrance ramp...
-
2. Mirrors
Mirrors: If provided, mirrors need to be mounted with the bottom edge of the reflecting surface no higher than 40 inches above the floor....
-
705.1 General
Detectable warnings shall consist of a surface of truncated domes and shall comply with 705. Figure 705.1 Size and Spacing of Truncated Domes...
-
Confirm that the vibrotactile indications work
Confirm that the vibrotactile indications work The tactile arrow or vibrating surface should vibrate rapidly only during the walk interval for the street....
-
5.4.3.1 Positioning Support Height for Imaging Equipment
Positioning supports should be positioned 3 to 6 inches above the transfer surface....
-
R305.2.6 Boarding Platforms
At boarding platforms for buses and rail vehicles, detectable warning surfaces shall be placed at the boarding edge of the platform....
-
11B-502.6.4 Marking
Each accessible car and van space shall have surface identification complying with either Section 11B-502.6.4.1 or 11B-502.6.4.2....
-
11B-502.6.4 Marking
Each accessible car and van space shall have surface identification complying with either Section 11B-502.6.4.1 or 11B-502.6.4.2. ...
-
11B-502.6.4 Marking
Each accessible car and van space shall have surface identification complying with either Section 11B-502.6.4.1 or 11B-502.6.4.2....
-
ASME
standard includes additional provisions for runway enclosures, electrical equipment and wiring, structural support, headroom clearance (which is 80 inches minimum), lower level access ramps...
-
Openings [1016.6]
Openings are gaps in the surface of an ORAR....
-
4.26.2* SIZE AND SPACING OF GRAB BARS AND HANDRAILS
The diameter or width of the gripping surfaces of a handrail or grab bar shall be 1-1/4 in to 1-1/2 in (32 mm to 38 mm), or the shape shall provide an equivalent gripping surface....
-
4.35.4 Bench
Where installed in conjunction with showers, swimming pools, or other wet locations, water shall not accumulate upon the surface of the bench and the bench shall have a slip-resistant surface...
-
11B-609.4 Position of grab bars
Grab bars shall be installed in a horizontal position, 33 inches (838 mm) minimum and 36 inches (914 mm) maximum above the finish floor measured to the top of the gripping surface, except...