[ADA Standards §§ 4.1.6(3)(d)(ii); 4.13.8] Yes No If No, replace threshold with one with beveled sides or add a sloped insert....
Search Results "Fire and Safety Standard"
Filters
Commonly Searched Documents
-
M5
-
D.1. - How does Section 508 affect the requirements development phase of an acquisition?
Section 508 requires agencies to take additional considerations into account when defining their needs for EIT – namely the Access Board’s standards....
-
1c
[ADA Standards 4.21.2] Yes __ No __ N/A __ Comments: ________________________________________...
-
Flange way gap
(DOT ADA Standard 810.10.)...
-
I1a
[ADA Standards § 4.31.2, Fig. 44 (a)] Yes No...
-
D4
[ADA Standards § 4.13.6, Fig. 25] Yes No If No, leave the door propped open or find another accessible entrance....
-
301.1 Scope
Chapter 3 shall apply to ICT where required by 508 Chapter 2 (Scoping Requirements), 255 Chapter 2 (Scoping Requirements), and where otherwise referenced in any other chapter of the 508 Standards...
-
4.17.4 Toe Clearances
In standard stalls, the front partition and at least one side partition shall provide a toe clearance of at least 9 in (230 mm) above the floor....
-
4.17.4 TOE CLEARANCES
In standard stalls, the front partition and at least one side partition shall provide a toe clearance of at least 9 in (230 mm) above the floor....
-
Stability or Stable Surface
stable surface is one that remains unchanged by contaminants or applied force, so that when the contaminant or force is removed, the surface returns to its original condition (2010 ADA Standards...
-
11B-607.2 Clearance
[2010 ADA Standards] 607.2 Clearance. Clearance in front of bathtubs shall extend the length of the bathtub and shall be 30 inches (760 mm) wide minimum....
-
11B-703.4.1 Height above finish floor or ground
[2010 ADA Standards] 703.4.1 Height Above Finish Floor or Ground....
-
11B-407.3.4 Door and signal timing
[2010 ADA Standards] 2. Destination-oriented elevators shall not be required to comply with 407.3.4....
-
11B-810.2.2 Dimensions
Access Board's Note to Reader: The Department of Transportation's ADA Standards indicate that compliance is required to the extent construction specifications are within a public entity's...
-
11B-806.3 Guest rooms with communication features
For headset or external amplification system compatibility, a standard subminiature jack installed in the telephone will provide the most flexibility. ◼...
-
11B-705.1.1.2 Dome spacing
[2010 ADA Standards] 705.1.2 Dome Spacing....
-
Final Regulatory Impact Analysis
The Final RIA embodies a comprehensive benefit-cost analysis of the final rules for both title II and title III and assesses the incremental benefits and costs of the 2010 Standards relative...
-
Section 36.103 Relationship to Other Laws (Section-By-Section Analysis and Response to Comments)
Paragraph (a) provides that, except as otherwise specifically provided by this part, the ADA is not intended to apply lesser standards than are required under title V of the Rehabilitation...
-
Organization of This Rule
Throughout this rule, the original ADA Standards, which are republished as Appendix D to 28 CFR part 36, will be referred to as the ‘‘1991 Standards.''...
-
Ampetronic MLD9 MultiLoop Driver Hearing System
MLD units are built to our exacting standards and are backed by our 5 year warranty....
-
E102.5 IETF (Section-by-Section Analysis)
This standard describes how to carry real-time text conversation session contents in RTP packets....
-
Kitchens and Kitchenettes
Section 804 of the 2010 Standards provides technical requirements for kitchens and kitchenettes....
-
Accessible Fishing Piers and Platforms
Sections 237 and 1005 of the 2010 Standards require at least twenty-five percent (25%) of railings, guards, or handrails (if provided) to be at a 34-inch maximum height (so that a person...
-
5.4.11 Transfer Support Structural Strength Recommendations for M301 and M302
The proposed technical criteria originated from provisions for grab bars in the 2010 Standards....
