"Type" refers to the design of the element (shelving, cabinets, closets) as well as the intended use (coat closets, supply closets)....
Search Results "Design Guideline"
Filters
Commonly Searched Documents
-
Scoping [4.1.3(12)]
-
Introduction
Introduction JAN’s Accommodation and Compliance Series is designed to help employers determine effective accommodations and comply with Title I of the Americans with Disabilities Act...
-
Long-Term Research
survey an appropriate children's population to keep up with design needs stemming from the trend toward mainstreaming in our schools....
-
Special thanks to:
Thanks to Alice Voigt and Michelle Cook (National Center on Accessibility) for their assistance in the conduct of the Exhibit Design Relating to Low Vision and Blindness workshop and to...
-
III-3.4100 Separate programs
Such programs must, however, be specifically designed to meet the needs of the individuals with disabilities for whom they are provided....
-
Landings [§405.7]
Landings must be designed to prevent the accumulation of water....
-
1.2.5 Ramps
However, when a design slope of 1:12 is indicated a tolerance of +0.5% is reasonable. Many accessibility experts consider a 2% cross slope to be the maximum....
-
11B-308.4 Suggested reach ranges for children
Where building elements such as coat hooks, lockers, or operable parts are designed for use primarily by children, the suggested dimensions of Table 11B-308.4 shall be permitted....
-
11B-1008.3 Transfer systems
Designers should minimize the distance between the points where a child transfers from a wheelchair or mobility device and where the elevated play components are located....
-
II-3.4100 Separate programs
Such programs must, however, be specifically designed to meet the needs of the individuals with disabilities for whom they are provided....
-
11B-1008.3 Transfer systems
Designers should minimize the distance between the points where a child transfers from a wheelchair or mobility device and where the elevated play components are located....
-
surface mounted toilet paper dispensers
Surface mounted dispensers are now being used for design and construction convenience, and they appear to pose an unnecessary hazard of injury due to the amount they project from the wall...
-
This is a great unit but it's not "recessed", it's semi-recessed.
Having the additional volume helps to minimize housekeeping trips for overflowing waste receptacles, but the designer must keep the 4" projection in mind when laying out the toilet room....
-
Sioux Chief Closet Flanges Demonstration Video
Innovative design can be seen and experienced with our TKO™ closet flange, with and without stainless steel ring, Open Flange, with and without stainless steel ring, our PushTite™, FullFlush...
-
Conditions for an Exception in FSTAG
A contractor's or designer's preference for different equipment is not a prevailing construction practices issue....
-
Polling places that cannot be remediated with temporary measures:
Building Entrance & Voting Area: The door at the designated accessible entrance does not provide at least 32 inches clear passage width when the door is open 90 degrees (1991 ADA Stds...
-
Accessible Parking
Accessible Parking When parking is provided for the public, designated accessible parking spaces must be provided, if doing so is readily achievable....
-
“Priority” Seating Method
“Priority” Seating Method Carriers may designate an adequate number of “priority” seats for passengers with a disability who meet the above requirements and who request a seating accommodation...
-
1193.35 Redundancy and selectability [Reserved] (Advisory Guidance)
Since there is no single interface design that accommodates all disabilities, accessibility is likely to be accomplished through various product designs which emphasize interface flexibility...
-
G. Response to 2008 NPRM Comments Concerning Movie Captioning and Video Description, Analysis and Discussion of Proposed Regulatory Approach
The ADA authorizes the Access Board to issue design guidelines for accessible buildings and facilities and requires that the design standards for buildings and facilities included in regulations...
-
The National Association of Home Builders Certified Aging-in-Place Specialist (CAPS)
The Certified Aging-in-Place Specialist (CAPS) designation program teaches the technical, business management, and customer service skills essential to competing in the fastest growing segment...
-
EXHIBIT I NOTICE OF SETTLEMENT OF FEDERAL DISABILITY DISCRIMINATION LAWSUIT UNITED STATES V. QUIKTRIP CORPORATION
information on how to submit a claim in several ways: (1) by sending an email with your name, address, and telephone number requesting claim information to [insert email address to be designated...
-
2010 ADA Standards
Recognized tolerances are not intended to apply to design work. It is good practice when specifying dimensions to avoid specifying a tolerance where dimensions are absolute....
