Openings are gaps in the surface of a beach access route....
Search Results "Hybrid Surface System"
Filters
Commonly Searched Documents
-
Openings [1018.6]
-
Outdoor Conditions [4.8.8]
Exterior ramps must be designed so that water does not accumulate on the ramp or landing surface. A slope up to 2% is allowed at landings for adequate drainage....
-
APPENDIX C
What was your pain/discomfort value associated with this surface (circle)?...
-
1011.4 Picnic Tables
This section requires picnic tables to comply with the technical requirements for dining surfaces in 902.3 of the Architectural Barriers Act Accessibility Guidelines, which requires the...
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
1133A.4 Countertops
A minimum linear length of 30 inches (762 mm) of countertop shall be provided for a work surface. ...
-
SuperDeck Fishing Dock & Deck
They delight dock operators and people like the stability and safety of our sturdy railing system, the molded-in non-slip tread surface, and the light cool comfort underfoot....
-
11B-703.4.1 Height above finish floor or ground
Tactile characters on signs shall be located 48 inches (1219 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest Braille cells and 60 inches (1524...
-
Transfer Supports Location and Configuration M301.3 and M302.3
Transfer Supports Location and Configuration M301.3 and M302.3 Location of the transfer supports shall be a minimum of 6 inches to a maximum of 19 inches from the top of the transfer surface...
-
11B-705.2 Detectable directional texture
transit boarding platforms shall comply with Figure 11B-705.2 and shall be 0.1 inch (2.5 mm) in height that tapers off to 0.04 inch (1.0 mm), with bars raised 0.2 inch (5.1 mm) from the surface...
-
STORY
[DSA-AC] That portion of a building or facility designed for human occupancy included between the upper surface of a floor and upper surface of the floor or roof next above....
-
AJW Architectural Products U592 1.6 Gallon Sanitary Napkin Disposal w/ Keyed Access Panel & Mounted Shelf - Surface Mounted
Product Features Fabricated of #22 gauge stainless steel with a #4 satin finish Waste receptacle has a 1.5 gallon capacity Bottom panel is hinged for easy removal of...
-
§ 38.125(b)(2)(i) Requirements
The controls shall be interlocked with the car brakes, propulsion system, or door, or shall provide other appropriate mechanisms or systems, to ensure that the car cannot be moved when the...
-
§ 38.95(b)(2)(i) Requirements
The controls shall be interlocked with the car brakes, propulsion system, or door, or shall provide other appropriate mechanisms or systems, to ensure that the car cannot be moved when the...
-
609 Grab Bars
Specifications address size, spacing, position, surfaces, fittings, and structural strength....
-
Floor Height [1013.4]
If the tent platform floor is raised above grade, the floor height must be no more than 19 inches when measured from the clear ground space to the tent platform surface....
-
2.7 Tread Obstacles
Where tread obstacles exist on the surface of an ORAR, they shall not exceed 1 inch (25 mm) in height....
-
ADA Technical Assistance Manual Addendum (10/29/02)
This document's guidance on potential conflicts between reassignment and seniority systems has been superseded....
-
3. Medical Diagnostic Equipment
rulemaking (NPRM) to remove the sunset provisions in the our existing accessibility standards for medical diagnostic equipment (MDE) related to the low-height specifications for transfer surfaces...
-
E101.4 Units of Measurement (Section-by-Section Analysis)
E101.4 Units of Measurement (Section-by-Section Analysis) This section would note measurements are stated in U.S. customary and metric units and that the values stated in each system...
-
Subject testing
A study was designed to investigate a correlation between surface roughness and WBV exposure to WC users in an attempt to determine which surfaces should be considered acceptable....
-
CS Pocket Insert Track Demo
CS Pocket Insert Track is a smooth running low profile track system suitable for incorporating into most pocket door frame assemblies. ...
-
Story
That portion of a building included between the upper surface of a floor and upper surface of the floor or roof next above....
-
1132A.4 Level floor or landing
Primary entry doors, required exit doors or secondary exterior doors with changes in height between the interior surface or floor level and the exterior surface or floor level shall comply...
