Mirrors shall be mounted with the bottom edge of the reflecting surface no higher than 40 in (1015 mm) from the floor (see Fig. 31)....
Search Results "End Transfer Surface"
Filters
Commonly Searched Documents
-
4.19.6* MIRRORS
-
Railings—Guardrails, Handrails, and Safety
Development should be consistent at both ends of the pathway....
-
1. Movable aisle armrests
The Department agrees that, if in a given aircraft, seats and seat pitches are configured so as to permit a horizontal transfer of a passenger from a boarding wheelchair to the aircraft...
-
Road Roughness Analysis
Serviceability is a criterion measure for highway surfaces based on surface roughness, which is then used as a determinant need for rehabilitation of highway surfaces....
-
Alterations and Water Closet Clearances in Single-User Toilet Rooms With In-Swinging Doors (Section-by-Section Analysis)
Standards allow a lavatory to be placed a minimum of 18 inches from the water closet centerline and a minimum of 36 inches from the side wall adjacent to the water closet, which precludes side transfers...
-
Section 36.308 Seating in Assembly Areas (Preamble, Section-by-Section Analysis)
In order to facilitate seating of wheelchair users who wish to transfer to existing seating, paragraph (a)(1) of the final rule adds a requirement that, to the extent readily achievable,...
-
Section 36.308 Seating in Assembly Areas (Section-By-Section Analysis and Response to Comments)
In order to facilitate seating of wheelchair users who wish to transfer to existing seating, paragraph (a)(1) of the final rule adds a requirement that, to the extent readily achievable,...
-
Salsbury Industries See Through Metal Locker Single Tier 3 Wide
and combination or key padlocks Salsbury Industries is an ISO 9001: 2008 certified company and has excelled in the field of manufacturing since 1936 Options Sloping hoods, end...
-
Salsbury Industries See Through Metal Locker Single Tier 1 Wide
and combination or key padlocks Salsbury Industries is an ISO 9001: 2008 certified company and has excelled in the field of manufacturing since 1936 Options Sloping hoods, end...
-
Minimum Number [9.1.2 and 9.1.3]
Rooms with combination roll-in/transfer showers are required in transient lodging facilities with more than 50 rooms....
-
11B-610.3 Shower compartment seats
In transfer-type showers, the seat shall extend from the back wall to a point within 3 inches (76 mm) of the compartment entry....
-
603.3 Mirrors
Mirrors located above lavatories or countertops shall be installed with the bottom edge of the reflecting surface 40 inches (1015 mm) maximum above the finish floor or ground....
-
402 Accessible Routes
Section 402 lists the various elements that can be part of an accessible route: walking surfaces, doorways, ramps, elevators, and platform lifts....
-
603.3 Mirrors
Mirrors located above lavatories or countertops shall be installed with the bottom edge of the reflecting surface 40 inches (1015 mm) maximum above the finish floor or ground....
-
11B-603.3 Mirrors
Mirrors located above lavatories or countertops shall be installed with the bottom edge of the reflecting surface 40 inches (1016 mm) maximum above the finish floor or ground....
-
603.3 Mirrors
Mirrors located above lavatories or countertops shall be installed with the bottom edge of the reflecting surface 40 inches (1015 mm) maximum above the finish floor or ground....
-
603.3 Mirrors
Mirrors located above lavatories or countertops shall be installed with the bottom edge of the reflecting surface 40 inches (1015 mm) maximum above the finish floor or ground....
-
4. Summary of Practice
The profile must be represented as a series of elevation values taken along with a series of horizontal distance values along the wheel track. 4.3 The PRI scale starts at zero for a surface...
-
11B-603.3 Mirrors
Mirrors located above lavatories or countertops shall be installed with the bottom edge of the reflecting surface 40 inches (1016 mm) maximum above the finish floor or ground....
-
11B-705.1.1.1 Dome size
Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (22.9 mm) minimum and 0.92 inch (23.4 mm) maximum, a top diameter of 0.45 inch (11.4 mm) minimum and...
-
III. Summary of Comments
Survey,3Â including equipment characteristics that affect patients ability to access and use medical equipment, such as: dimensions of the equipment (e.g. height, width, length,) contact surfaces...
-
Mockett SDH1-SSS Sliding Door Hardware Set
Spring-loaded door stops are included for either end to gently stop the door from extending beyond the door opening....
-
Supergrit Safety Treads
Nosings shall terminate not more than 4" (101.6 mm) from ends of steps for poured concrete stairs; for concrete filled pan stairs, nosings shall be full length of steps less 1/8" (3.05 mm...
-
Allegion Falcon 24 Series Touch Bar Exit Device
Features and Benefits Streamlined design includes flush-end cap for clean lines and a more attractive installation Stainless steel pushpad cover for a scratch-resistant...
